Exterior (external body elements) Skoda Yeti

Body — specifications
Gaps between body elements, mm Note: To measure gaps between body elements, use control plate set #3371. Gaps in the front 1. not less than 3.0; 2. 4.5±1.5; 3,12. 3.5±0.5; 4. 6.7±1; 5. 2.2±0.5; 6. 2.6±0.5; 7. 3.5±0.5...

Body — general information
This chapter covers repair and removal/installation procedures for the most frequently serviced components. Procedures related to welding operations are not considered. Removal/installation of some finishing elements...

Removal and installation the hood lock holder and its parts
1. The hood latch holder is a safety component and cannot be repaired; if damaged, replacement is carried out. The installation details of the bonnet lock holder are shown in the illustration. 2.1. Bonnet Lock Holder...

Removal and installation of the front wing and its parts
1. Front wing installation details are shown in the illustration. 3.1. Front left wing installation details 1. Soundproofing panel; 2. Nut, 8 Nm; 3. Front left wing; 4. Bolt, 8 Nm; 5. Upper wing support; 6. Lower wing...

Removal and installation of bumpers and towing hitch parts
1. Front bumper cover installation details are shown in the illustration. To remove both parts of the trim, unscrew the bolts (6, 1, 2 and 5), remove the rivets (7), unscrew the bolts (8) and pull the trim forward,...

Removal and installation the upper sunroof assembly and roof rails
1. Details of installation of roof rails are shown in the illustration. To remove the roof rail, remove the covers (1) and unscrew the bolts (3). 5.1. Roof rail installation details 1. Lid; 2. Railing; 3. Bolt, 10 Nm;...

Removal and installation of sound insulation panels, mudguards, roof rails, moldings, covers, shields and other body trims
1. Details of installation of wheel arch liners are shown in the illustrations. To remove the locker, you must remove the corresponding wheel (if necessary) and unscrew the fasteners. When installing, tighten the screws...

Removal and installation of the hood and its parts
1. The hood installation details are shown in the illustration. 7.1. Bonnet installation details 1. Hood; 2. Support stand; 3. Windshield washer fluid supply nozzles; 4. Loop; 5, 6. Bolts, 20 Nm; 7. Rubber bushing; 8....

Removal and installation the fuel filler flap with cover
1. Unscrew the bolt (3 in the illustration) and carefully pull the hatch assembly (2) slightly out of the rear wing, avoiding damage to the paintwork. 8.1. Details of installation of the hatch with cover 2. Pull the...

Removal and installation of the tailgate and its parts
Note: The description of the removal of parts installed on the inside of the door is given in Parts B . 1. The installation details of the tailgate are shown in the illustration. 9.1. Tailgate installation details 1....

Removal and installation of side doors and their parts
Note: The removal and installation of the outside mirror is described in Section 11 ; a description of the removal of parts installed on the inside of the door is given in Part B. Note: After working with the locking...

Removal and installation the outside rearview mirror
1. The assembly details of the outside rearview mirror are shown in the illustration. To remove the mirror assembly, remove the front door trim ( see Part B ) and the inner cover (1), disconnect the connector (7) and...

This section is available on russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

Read similar sections on other Skoda models

➧ Body and interior: Exterior (external elements) Skoda Fabia 2 (2007-2014)
➧ Body and interior: Exterior (external elements) Skoda Rapid 1 (2012-2022)
➧ Body and interior: Exterior (external elements) Skoda Octavia 1 (1996-2004)
➧ Body and interior: Exterior (external elements) Skoda Superb 2 (2008-2015)
➧ Body and interior: Exterior (external elements) Skoda Kodiaq 1 (2016-2024)
➧ Body and interior: Exterior (external elements) Skoda Felicia (1994-2001)

Link to this section in various formats

TEXTHTMLBB Code

Yeti (2009-2017)