Petrol engine 1.8 l (CDAA/CDAB) of car Skoda Yeti

Removal and installation of the engine and powertrain supports
Removal and installation Note: The engine is removed from underneath the engine compartment downwards together with the transmission. All removed electrical wiring ties and clamps must be in their original places during...

Removal and installation the accessory drive belt, its tensioner and auxiliary bracket
1. The details of the auxiliary drive installation are shown in the illustration. 24.1. Auxiliary drive parts 1. Crankshaft pulley; 2. Sealing ring, subject to replacement; 3. Pulley bolt 1, to be replaced, 150 Nm, then...

Removal and installation the crankshaft pulley, replacing the front crankshaft oil seal
Removal and installation the crankshaft pulley Note: Crankshaft pulley installation details are shown on illustrations 24.1 . 1. Remove the sound insulation under the engine compartment, as well as the right front wheel...

Removing and installing the flywheel and rear oil seal (sealing flange)
1. The installation details of the rear sealing flange and flywheel are shown in the illustration. 26.1. Rear sealing flange and flywheel installation details 1. Cylinder block; 2, 8. Centering sleeve; 3. Sealing...

Removal and installation the N205 valve and timing chain covers
1. The installation details of the N205 sensor and timing chain covers are shown in the illustration. 27.1 Installation details of the N205 sensor and timing chain covers 1. O-ring, subject to replacement, lubricate...

Removal and installation the timing chain
1. Timing chain installation details are shown in the illustration. 28.1. Timing chain installation details 1, 5. Bolt, 9 Nm; 2. Chain tensioner 12; 3. Chain tension bar 12; 4, 14. Guide pins, 20 Nm; 6. Timing phase...

Removal and installation balance shafts and their drive chain
Balance shaft drive chain 1. The details of the installation of the balance shafts and their chains are shown in the illustration. 29.1. Details of installation of balance shafts and their chains 1, 10. Bolt, 9 Nm; 2....

Removal and installation the cylinder head
Note: Do not remove the open valve guards from the new cylinder head until you are ready to install the cylinder head. If a new cylinder head or gasket is installed, replace the coolant. Use new cylinder head bolts and...

Work with the gas distribution mechanism, removal and installation of the cylinder head cover
1. The design of the timing belt is shown in the illustration. 31.1 Timing belt parts 1. Exhaust valve, machining is not allowed, only lapping; 2. Cylinder head; 3. Valve guide bushing; 4. Oil deflector cap; 5. Valve...

Work with the lubrication system
1. The installation details of the lubrication system components are shown in the illustrations. 32.1a. Oil pan and oil pump installation details 1. Sensor "G266" of engine oil level and temperature; 2. Sealing ring,...

Features of major engine repair, replacement of needle bearing and CKP sensor rotor
Caution: The presence of metal shavings or large quantities of small metal particles found during engine rebuild may indicate damage to the crankshaft and connecting rod bearings. To prevent further damage, thoroughly...

This section is available on russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

Read similar sections on other Skoda models

➧ Power unit: Petrol engines Skoda Rapid 1 (2012-2022)
➧ Power unit: Petrol engines 3.6 l Skoda Superb 2 (2008-2015)
➧ Power unit: Petrol engine 1.4 l Skoda Kodiaq 1 (2016-2024)
➧ Power unit: Petrol engine 1.6 l Skoda Felicia (1994-2001)

Link to this section in various formats

TEXTHTMLBB Code

Yeti (2009-2017)