Gasoline engine 1.6 liter car Skoda Felicia

Engine repair without removing from the car
Rules for using the material Chapters This Part of the Chapter is devoted to the repair of the 1.6 L engine, not associated with its removal from the car (in situ). Most of the procedures discussed herein are written on...

Description of the main components and mechanisms of the engine
Cylinder block and its internal components 1 - Main bearing shell; 2 - Main bearing cap mounting bolts; 3 - Main bearing caps; 4 - Third (thrust) main bearing shells; 5 - Lower thrust half rings; 6 - Flywheel mounting...

Bringing the piston of the first cylinder to the top dead center (TDC) position
General information Note: The material presented in this subsection is only meaningful if the distributor, high-voltage wires and timing belt are installed correctly. The timing belt is placed on the toothed wheels of...

Checking the compression pressure in the cylinders
1. If the engine output efficiency decreases, as well as if misfires occur that cannot be linked to malfunctions of the ignition and fuel systems, the compression pressure in the cylinders should be measured, the...

Removal and installation the timing belt and its covers
General information The main function of the timing belt is to drive the camshaft from the crankshaft. In parallel, the belt is also used to drive the water pump of the engine cooling system. Slipping or breaking of the...

Removal, inspection and installation of gears and timing belt tensioner
General information Before starting the procedure, the engine and the car should be immobilized: a) Disconnect the negative battery cable. b) Support the rear wheels of the car with wedges and apply the parking brake....

Removal, installation and adjusting the accessory drive belt
General information Depending on the vehicle's configuration, the auxiliary drive belt is used to drive devices such as the alternator, steering pump and air conditioning compressor from the crankshaft pulley. On some...

Removal and installation the cylinder head cover
Removal 1. Using a socket wrench, remove the three mounting head bolts. 2. Remove the cover from the cylinder head - if necessary, tap it around the perimeter with a soft-faced hammer to release it. 3. Remove the gasket...

Replacing the camshaft seal
1. Remove the accessory drive belt (see section Removal, installation and adjustment of the tension force of the auxiliary drive belt ). 2. Remove the timing belt covers, crankshaft pulley, bring the piston of the first...

Replacing crankshaft seals
Front oil seal 1. Drain the engine oil. 2. Remove the accessory drive belt (see section Removal, installation and adjustment of the tension force of the auxiliary drive belt ). 3. Remove the crankshaft pulley, outer...

Removal and installation the cylinder head assembly with the intake and exhaust manifold
Removal 1. Park your car on a spacious, level, horizontal area with a hard surface. 2. Disconnect the negative cable from the battery. Note: If your vehicle's stereo system is equipped with a security device, make sure...

Checking the serviceability of hydraulic tappets
Caution: After installing hydraulic tappets, wait at least 30 minutes before starting the engine (it is recommended to postpone the launch until the next morning), otherwise, the risk of pistons colliding with valves...

Removal, condition check and installation of the flywheel
General information The flywheel is made of steel and is equipped with a toothed rim. It is fastened to the crankshaft flange with six M10x1 bolts with TORX heads. The flywheel is designed for installation of a clutch...

Checking the condition and replacing the power unit supports
Examination 1. Jack up the front of the car and place it on supports. 2. Check the rubber support pads for cracks, signs of hardening, rubber peeling off the metal base and other mechanical damage. If such defects are...

Removal and installation the engine oil pan
Removal 1. Park the car on a flat, horizontal surface, preferably with a hard surface. Apply the parking brake and chock the rear wheels. 2. Jack up the front of the car and place it on supports. 3. Disconnect the...

Removal and installation the oil pump and oil intake
Layout diagram of the main components of the lubrication system 1 - Cylinder block; 2 - Bolt; 3 - Oil filter; 4 - Bolt; 5 - Sealing gasket; 6 - Bolt; 7 - Oil pan; 8 - Sealing gasket; 9 - Drain plug; 10 - Generator and...

This section is available on russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

Read similar sections on other Skoda models

➧ Power unit: Petrol engines Skoda Rapid 1 (2012-2022)
➧ Power unit: Petrol engines 1.8/2.0 l Skoda Superb 2 (2008-2015)
➧ Power unit: Petrol engine 1.4 l Skoda Kodiaq 1 (2016-2024)
➧ Power unit: Petrol engine 1.8 l Skoda Yeti (2009-2017)

Link to this section in various formats

TEXTHTMLBB Code

Felicia (1994-2001)