Drive shafts of car Skoda Yeti
Drive shafts and wheel hubs — specifications
Types and volumes of working fluids - see Specifications to Chapter 1 Rear Drive Shaft Flange Diameter (rear final drive 0BR), mm - 100 Front drive shaft flange diameter, mm RKPP 0A4, 0AJ — 100 Manual transmission 02Q —...
Types and volumes of working fluids - see Specifications to Chapter 1 Rear Drive Shaft Flange Diameter (rear final drive 0BR), mm - 100 Front drive shaft flange diameter, mm RKPP 0A4, 0AJ — 100 Manual transmission 02Q —...
Drive shafts and wheel hubs — general information
Caution: Avoid excessive stress and damage to the CV joint boots of the drive shafts; do not bend the shaft all the way; do not allow the drive shafts to fall, as this may cause damage to the inside of the CV joint...
Caution: Avoid excessive stress and damage to the CV joint boots of the drive shafts; do not bend the shaft all the way; do not allow the drive shafts to fall, as this may cause damage to the inside of the CV joint...
Replacing the front wheel hub assembly, unscrewing and tightening the hub bolt
1. The front wheel hubs together with the hub bearings form single, non-separable units, secured to the steering knuckles. The installation details of the steering knuckle and front wheel hub assembly are shown in the...
1. The front wheel hubs together with the hub bearings form single, non-separable units, secured to the steering knuckles. The installation details of the steering knuckle and front wheel hub assembly are shown in the...
Removal and installation the rear hub assembly and its holder
1. The installation details of the rear hub assembly are shown in the illustrations. The hub and wheel bearing are combined into a non-separable, maintenance-free unit, secured to the holder. 3.1a. Rear hub assembly and...
1. The installation details of the rear hub assembly are shown in the illustrations. The hub and wheel bearing are combined into a non-separable, maintenance-free unit, secured to the holder. 3.1a. Rear hub assembly and...
Removal and installation drive shafts
Note: Depending on the transmission installed, one of two front drive shaft options may be installed: "VL100" (without cover between inner hinge and drive flange) or "VL107" (with cover between inner hinge and drive...
Note: Depending on the transmission installed, one of two front drive shaft options may be installed: "VL100" (without cover between inner hinge and drive flange) or "VL107" (with cover between inner hinge and drive...
Repair of drive shafts
1. The drive shaft assembly parts are shown in the illustrations. 5.1a. Front Drive Shaft Installation Details "VL100" 1. Outer CV joint, replaced as an assembly; 2. Hub bolt, to be replaced, 70 Nm, then tighten to an...
1. The drive shaft assembly parts are shown in the illustrations. 5.1a. Front Drive Shaft Installation Details "VL100" 1. Outer CV joint, replaced as an assembly; 2. Hub bolt, to be replaced, 70 Nm, then tighten to an...
Removal and installation the angular transmission
Models with DSG "02E" 1. Remove the DSG ( see Chapter 7 ) together with the angular transmission, fix it on the mounting stand. 2. Unscrew the conical bolt securing the right flange shaft using the T10107A head. In this...
Models with DSG "02E" 1. Remove the DSG ( see Chapter 7 ) together with the angular transmission, fix it on the mounting stand. 2. Unscrew the conical bolt securing the right flange shaft using the T10107A head. In this...
Removal and installation the propeller shaft
1. The details of the cardan shaft installation are shown in the illustration. 7.1. Cardan shaft installation details 1. Angular transmission 2 Bolts M 10x30, 3 pcs., 60 Nm; 3. Cardan shaft, when installing, bearing 5...
1. The details of the cardan shaft installation are shown in the illustration. 7.1. Cardan shaft installation details 1. Angular transmission 2 Bolts M 10x30, 3 pcs., 60 Nm; 3. Cardan shaft, when installing, bearing 5...
Repair of the cardan shaft
1. The cardan shaft is balanced during manufacturing. Since balancing in a repair shop is impossible, if the shaft is faulty, it must be replaced completely. 2. If any parts of the cardan shaft are damaged, it will need...
1. The cardan shaft is balanced during manufacturing. Since balancing in a repair shop is impossible, if the shaft is faulty, it must be replaced completely. 2. If any parts of the cardan shaft are damaged, it will need...
Removal and installation the unit
1. The assembly details of the all-wheel drive control unit "J492" are shown in the illustration. Block "J492" and valve "N373" are calibrated together and are also replaced together. 9.1. Assembly details of the "J492"...
1. The assembly details of the all-wheel drive control unit "J492" are shown in the illustration. Block "J492" and valve "N373" are calibrated together and are also replaced together. 9.1. Assembly details of the "J492"...
Removal and installation the pump
1. Turn off the ignition. 2. Place a drip tray under the Haldex coupling to collect the fluid. 3. Unscrew the filler plug ( And in illustration 4.41d of Chapter 1 ), unscrew the drain plug (B) and drain the Haldex...
1. Turn off the ignition. 2. Place a drip tray under the Haldex coupling to collect the fluid. 3. Unscrew the filler plug ( And in illustration 4.41d of Chapter 1 ), unscrew the drain plug (B) and drain the Haldex...
Removal and installation the Haldex coupling
1. The Haldex coupling installation details are shown in the illustration. 11.1 Haldex coupling installation details 1. The sealing ring between the clutch and the rear final drive must be replaced; 2. Haldex coupling...
1. The Haldex coupling installation details are shown in the illustration. 11.1 Haldex coupling installation details 1. The sealing ring between the clutch and the rear final drive must be replaced; 2. Haldex coupling...
Removal and installation the rear final drive with differential
1. The installation details of the rear final drive are shown in the illustration. 12.1. Rear final drive installation details Arrow Direction of movement; 1. Rear subframe; 2. Drive shaft; 3. Rear final drive; 4, 8....
1. The installation details of the rear final drive are shown in the illustration. 12.1. Rear final drive installation details Arrow Direction of movement; 1. Rear subframe; 2. Drive shaft; 3. Rear final drive; 4, 8....
Removal and installation sensors
1. Description of the removal and installation of the assembly of the D/V "F" brake lights and the "F47" clutch pedal position sensor is given in Section 5 . 2. The ESP sensor assembly "G419", which includes the lateral...
1. Description of the removal and installation of the assembly of the D/V "F" brake lights and the "F47" clutch pedal position sensor is given in Section 5 . 2. The ESP sensor assembly "G419", which includes the lateral...
This section is available on russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian
Read similar sections on other Skoda models
➧ Transmission: Drive shafts Skoda Rapid 1 (2012-2022)
➧ Transmission: Drive shafts Skoda Kodiaq 1 (2016-2024)
➧ Transmission: Drive shafts Skoda Felicia (1994-2001)
Link to this section in various formats
TEXTHTMLBB Code
- General information
- Introduction to manual
- Controls and instruments
- Maintenance
- Power unit
- Petrol engine 1.2 l
- Petrol engine 1.4 l
- Petrol engine 1.8 l
- Diesel engine 2.0 l
- Cooling system
- Power and control system
- Exhaust system
- Ignition and preheating systems
- Starting and charging system
- Transmission
- Clutch
- Manual gearbox
- 7-speed gearbox DSG «0AM»
- 6-speed gearbox DSG «02E»
- Drive shafts
- Chassis (running gear)
- Brake system
- Front suspension
- Rear suspension
- Steering
- Body and interior
- Heating and air conditioning
- Exterior (external elements)
- Interior (internal elements)
- Electrical equipment
- Equipment and devices
- Lighting and signaling
- Electrical diagrams

