5.1a. Front Drive Shaft Installation Details "VL100" 1. Outer CV joint, replaced as an assembly; 2. Hub bolt, to be replaced, 70 Nm, then tighten to an angle of 90°; 3. Right drive shaft; 4. Large clamp of boot 5, subject to replacement; 5. Outer CV joint boot; 6. Small clamp of boot 5, subject to replacement; 7. Disc spring, installed with a smaller diameter towards the end of the shaft; 8. Support ring; 9. The retaining ring, subject to replacement, is inserted into the groove on the shaft; 10. The inner CV joint boot, without a ventilation hole, is removed from the CV joint using a mandrel. Before installation, apply D454 300A2 grease to the sealing surface; 11. Clamp of anther 10; 12. Left drive shaft; 13. Washer, subject to replacement; 14. Bolts, subject to replacement, 10 Nm, then 40 Nm (bolts M8x48) or 70 Nm (bolts M0x52); 15. Retaining ring; 16. Self-adhesive gasket, replaceable, glued to the CV joint; 17. Inner CV joint, replaced as an assembly; 18. Disc spring, installed with a larger diameter towards the end of the shaft
5.1b. Front Drive Shaft Installation Details "VL107" 1. Outer CV joint, replaced as an assembly; 2. Hub bolt, to be replaced, 70 Nm, then tighten to an angle of 90°; 3. Small clamp of boot 4, subject to replacement; 4. Outer CV joint boot; 5. Large clamp of boot 4, subject to replacement; 6. Disc spring, installed with a smaller diameter towards the end of the shaft; 7. Support ring; 8. The retaining ring, subject to replacement, is inserted into the groove on the shaft; 9. The inner CV joint boot, without a ventilation hole, is removed from the CV joint using a mandrel. Before installation, apply D454 300A2 grease to the sealing surface; 10. Disc spring, installed with a large diameter at the end of the shaft; 11. Small boot clamp 9, subject to replacement; 12. Drive shaft; 13. Cover, subject to replacement; 14. Retaining ring; 15. Self-adhesive gasket, replaceable, glued to the CV joint; 16. Inner CV joint, replaced as an assembly; 17. Cover, removed using a mandrel, apply D454 300A2 grease to the sealing surface before installation; 18. Washer, subject to replacement; 19. Bolts, subject to replacement, 10 Nm, then 40 Nm (bolts M8x48) or 70 Nm (bolts M0x52); 20. Large boot clamp 9, subject to replacement
5.1c. Rear Drive Shaft Installation Details 1. Outer CV joint, replaced as a whole, during installation it is driven in with a plastic hammer until it stops; 2. Hub bolt, to be replaced, 70 Nm, then tighten to an angle of 90°; 3. Drive shaft; 4. Small clamp of boot 5, subject to replacement; 5. Outer CV joint boot; 6. Large clamp of boot 5, subject to replacement; 7. Disc spring, installed with a smaller diameter towards the end of the shaft; 8. Support ring; 9. The retaining ring, subject to replacement, is installed in the groove on the shaft; 10. Small clamp of boot 11, subject to replacement; 11. The inner CV joint boot, without a ventilation hole, is removed from the CV joint using a mandrel. Before installation, apply D454 300A2 grease to the sealing surface; 12. Bolts M8x48, subject to replacement, 10 Nm, then tighten to a force of 20 Nm, then tighten to an angle of 180°; 13. Washer, subject to replacement; 14. Retaining ring, subject to replacement; 15. Gasket, subject to replacement; 16. Inner CV joint, replaced as an assembly; 17. Disc spring with internal splines, installed with a larger diameter towards the end of the shaft
(Material is available on the website: «Skodabook.ru»)