Car security systems Skoda Kodiaq 1

Airbags — safety precautions
Safety precautions when working with the security system 1. Work on the airbag may only be started no later than 3 minutes after the ignition key has been set to the OFF position and the wire has been disconnected from...

Airbag Control Module Description
The command to deploy the airbags comes from the SRS unit, which receives a signal from the front and side impact sensors. 1. DC-DC Converter: Located in the power supply unit, it contains a step-up/step-down converter...

Airbag Control Unit — removal and installation
Caution: Do not change the original position of the electronic control unit of the passive restraint system while the unit is connected to the power supply and the ignition is on. Otherwise, the airbag may deploy...

Driver's side front airbag removal and installation
Caution: Do not connect electrical measuring instruments to the airbag terminals. It is possible that the pyropatron may spontaneously trigger, resulting in serious injuries. Caution: To prevent accidental airbag...

Front passenger airbag removal and installation
Caution: Always store the passenger airbag module with the housing facing down and the decorative cover facing up after removal. Never store the airbag module with the cover facing down. Failure to follow this...

Side airbag — removal and installation
Caution: Always store the side airbag module with the body facing down and the cover facing up after removal. Never store the airbag module with the cover facing down. Failure to follow this instruction may result in...

Rear seat side airbag — removal and installation
Caution: Always store the side airbag module with the body facing down and the cover facing up after removal. Never store the airbag module with the cover facing down. Failure to follow this instruction may result in...

Side curtain airbag — removal and installation
Caution: After removal, always store the airbag module with the housing facing down and the decorative cover facing up. Never store the airbag module with the cover facing down. Failure to follow this instruction may...

Knee airbag module — removal and installation
Caution: Always store the knee airbag module with the body facing down and the cover facing up after removal. Never store the airbag module with the cover facing down. Failure to follow this instruction may result in...

Front impact sensor — removal and installation
Caution: Do not connect electrical measuring instruments to the airbag terminals. It is possible that the pyropatron may spontaneously trigger, resulting in serious injuries. Note: Repair of passive safety system...

General rules for the disposal of passive safety system components
Attention: If the vehicle is to be scrapped, the airbags and seat belt pretensioners inside the vehicle must be activated. If the vehicle is planned to be used in the future and only the airbag modules need to be...

Disposal of airbag modules and pretensioners
Once activated, airbag modules and seat belt pretensioners must be disposed of in accordance with current environmental protection legislation. To do this, you need to do the following: 1. The pyropatnik is very hot...

Front seat belts — removal and installation
Attention: After an accident, it is always necessary to perform a complete technical check of the passive safety system components described below. Inertia seat belt tensioners. Seat belt locks (buckles). Seat belt...

Center Row Seat Belt — removal and installation
1. Remove the seat assembly (for more details, see the relevant section in the chapter " Body "). 2. Remove the side panel of the luggage compartment trim (for more details, see the corresponding section in the chapter...

Front seat belt buckle — removal and installation
1. Remove the front seat (for more details, see the relevant section in the chapter " Body "). 2. Unscrew the mounting bolt (2) (tightening torque 40 Nm), shown in the figure below. 3. Remove the seat belt buckle (1) as...

Checking the winding machine (locking operation)
The automatic seat belt retractor mechanism has two locking functions. In the first function, the block is triggered and blocks the belt when it is suddenly pulled out of the winding machine (belt pull-out...

This section is available on russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

Read similar sections on other Skoda models

➧ Body and interior: Security systems Skoda Rapid 1 (2012-2022)

Link to this section in various formats

TEXTHTMLBB Code

Kodiaq 1 (2016-2024)