Front suspension of the car Skoda Kodiaq 1

Front Suspension Components
Components 1. Anti-roll bar; 2. Fastening nut, tightening torque 80 Nm; 3. Front suspension shock absorber assembly; 4. Crossbar stabilizer bar; 5. Front suspension subframe assembly; 6. Fastening bolt, tightening...

Front Suspension Subframe Assembly — removal and installation (without steering rack)
Removal Note: The front suspension subframe is removed as an assembly with the control arms. 1. Loosen the mounting bolts. 2. Raise the car on a lift. Check and ensure that the vehicle is securely fixed to the lift...

Front Suspension Subframe Assembly — removal and installation (from steering rack)
Removal 1. Set the steering wheel to the straight-ahead position. For models with mechanical ignition key 2. Remove the key from the ignition switch to lock the steering column. For models with electronic ignition key...

Anti-roll bar — removal and installation
Removal 1. Release the front wheel fastening elements. 2. Raise the car on a lift. Check and ensure that the vehicle is securely fixed to the lift supports. 3. Remove the front wheels as an assembly. 4. Remove the lower...

Anti-roll bar strut — removal and installation
1. Raise the complete vehicle on a lift. Check and ensure that the vehicle is securely fixed to the lift supports. 2. Loosen the mounting nut (arrow) and disconnect the anti-roll bar strut (1) from the shock absorber...

Shock absorber strut components
Components 1. Upper spring support; 2. Shock absorber assembly; 3. Fastening bolt, tightening torque 70 Nm + 180 degrees; 4. Steering knuckle; 5. Fastening nut; 6. Anther; 7. Spring; 8. Shock absorber support bearing;...

Shock absorber strut — removal and installation
Removal 1. Unscrew the bolt securing the drive shaft to the front wheel hub. Attention: After loosening the hub nuts, the load on the hub bearings should be eliminated. Otherwise, the weight of the vehicle will damage...

Shock absorber strut repair
Removal the coil spring 1. Install the shock absorber clamp "VAG 1752/20" (4) in a vice. 2. Fix the shock absorber strut in the clamp "VAG 1752/20" (4). 3. Compress the coil spring with a device "VAG 1752/1", so that...

Front Lower Control Arm — components
Components 1. Steering knuckle; 2. Fastening nut, tightening torque 60 Nm; 3. Ball joint; 4. Fastening nut, tightening torque 40 Nm + 45 degrees; 5. Lower suspension arm; 6. Front silent block; 7. Fastening bolt,...

Lower control arm of the front suspension — removal and installation (models with manual or manual transmission)
Removal 1. Loosen the front wheel mounting bolts. 2. Raise the car on a lift. Check and make sure that it is securely fastened to the lift supports. 3. Remove the front wheels as an assembly. 4. Remove the lower...

Lower control arm of the front suspension — removal and installation (models with odl, ogc manual transmission)
Removal 1. Set the steering wheel to the straight-ahead position. For models with mechanical ignition key 2. Remove the key from the ignition switch to lock the steering column. For models with electronic ignition key...

Checking the condition of the ball joint
Checking axial play First, pull the triangle lever down forcefully in the direction of the arrow, and then push it up again, as shown in the figure below. Checking the radial clearance Grasp the wheel at the bottom and...

Removal and installation the ball joint
Note: Necessary tools, measuring instruments and auxiliary equipment Ball joint puller "3287A". Torque wrench "VAG 1332". Jack for engines and transmission units -VAG 1383 A-. Angle tightening key "VAG 1756". Removal 1....

Steering knuckle — removal and installation
Removal 1. Loosen the nut securing the drive shaft to the front wheel hub. Attention: After loosening the hub nut, remove any load from the hub bearings. Otherwise, the weight of the vehicle will damage the wheel...

Setting the suspension to a position corresponding to the vehicle's curb weight
Necessary special devices, control and measuring instruments, as well as auxiliary means Engine and gearbox mount "VAG 1383 A". Tension belt "T10038". Stop "T10149". Description of the process Note: All bolts of the...

This section is available on russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

Read similar sections on other Skoda models

➧ Chassis (running gear): Front suspension Skoda Fabia 2 (2007-2014)
➧ Chassis (running gear): Front suspension Skoda Rapid 1 (2012-2022)
➧ Chassis (running gear): Front suspension Skoda Octavia 3 (2013-2019)
➧ Chassis (running gear): Front suspension Skoda Superb 2 (2008-2015)
➧ Chassis (running gear): Front suspension Skoda Yeti (2009-2017)

Link to this section in various formats

TEXTHTMLBB Code

Kodiaq 1 (2016-2024)