Cooling system (petrol 1.4 l) of car Skoda Kodiaq 1

Replacing the coolant
Note: If the coolant is to be reused, it must be drained into a clean container prepared in advance. 1. Open the coolant expansion tank cap (arrow) as shown in the figure below. 2. Remove the soundproofing coating. 3....

Water pump — general view
General appearance 1. Thermostat housing; 2. Thermostat assembly; 3. Gasket; 4. Water pump; 5. Fastening screw, tightening torque during installation 8 Nm; 6. Gasket; 7. Upper cover of the timing belt; 8. Mounting bolt,...

Additional electric pump for the cooling system
General appearance 1. Coolant recirculation pump; 2. Water hose; 3. Fastening screw, tightening torque during installation 8 Nm; 4. Water hose.

Coolant temperature sensor
General appearance 1. Sealing ring; 2. Coolant temperature sensor at the radiator outlet; 3. Support ring; 4. Sealing ring; 5. Coolant temperature sensor; 6. Mounting bolt, tightening torque during installation 8 Nm; 7....

Water pump — removal and installation
Removal 1. Drain the coolant ( for more details, see the relevant section in this chapter ). 2. Remove the battery and the battery support plate (for more details, see the relevant section in the chapter " Engine...

Toothed pulley of water pump drive
Removal and installation Removal 1. Drain the coolant ( for more details, see the relevant section in this chapter ). 2. Remove the battery and the battery support plate (for more details, see the relevant section in...

Electric coolant recirculation water pump
Removal and installation Removal 1. Open and remove the coolant expansion tank cap as shown in the figure below. Caution: When the engine has reached normal operating temperature, the coolant in the cooling system is...

Thermostat (large circle) — removal and installation
Removal Note: If the coolant is to be reused, it must be drained into a clean container prepared in advance. 1. Open the coolant expansion tank cap (arrow) as shown in the figure below. 2. Remove the soundproofing...

Thermostat (small circle) — removal and installation
Removal 1. Drain the coolant ( for more details, see the relevant section in this chapter ). 2. Remove the battery and the battery support plate (for more details, see the relevant section in the chapter " Engine...

Coolant temperature sensor
Removal and installation Removal Note: The engine must be cold. 1. Open the expansion tank cap to relieve excess pressure in the cooling system, then close the cap, screwing it on until you hear a distinctive click. 2....

Radiator outlet coolant temperature sensor
Removal and installation Removal Note: The engine must be cold. 1. Open the expansion tank cap to relieve excess pressure in the cooling system, then close the cap, screwing it on until you hear a distinctive click. 2....

Elements of the engine cooling system (side part of the internal combustion engine)
Elements of the engine cooling system (side part of the internal combustion engine) 1. Water hose; 2. Water pipe; 3. Fastening screw, tightening torque 8 Nm; 4. Water hose; 5. Water hose; 6. Cooling system line tube; 7....

Cooling system hoses — removal and installation
Removal Caution: When the engine has reached normal operating temperature, the coolant in the cooling system is under pressure, so there is a high risk of burns if the expansion tank cap is opened carelessly. Therefore,...

This section is available on russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

Read similar sections on other Skoda models

➧ Petrol engines 1.6 l: Cooling and lubrication system Skoda Fabia 2 (2007-2014)
➧ Power unit: Cooling system Skoda Rapid 1 (2012-2022)
➧ Power unit: Cooling system Skoda Octavia 1 (1996-2004)
➧ Power unit: Cooling system Skoda Superb 2 (2008-2015)
➧ Power unit: Cooling system Skoda Yeti (2009-2017)
➧ Power unit: Cooling and heating Skoda Favorit (1987-1994)

Link to this section in various formats

TEXTHTMLBB Code

Kodiaq 1 (2016-2024)