Engine lubrication system (petrol) of vehicle Skoda Kodiaq 1

Lubrication system — 1.4l petrol engine
Components 1. Mounting bolt, tightening torque during installation 8 Nm + tighten an additional 90°; 2. Engine oil level and temperature sensor; 3. Sealing ring; 4. Oil pan drain plug; 5. Sealing ring; 6. Oil pan; 7....

Engine oil level and temperature sensor — removal and installation
Removal 1. Drain the engine oil into a pre-prepared container. 2. Disconnect the wiring harness connector (3) shown in the figure below. 3. Loosen the mounting nuts (1), then remove the engine oil level and temperature...

Oil pan — removal and installation
1. Drain the engine oil into a pre-prepared container. 2. Disconnect the wiring harness connector (1) for the engine oil temperature and level sensor, as shown in the figure below. 3. Unscrew the mounting bolts in the...

Upper part of the engine crankcase
Removal and installation 1. Unscrew the mounting bolts and remove the air conditioning compressor assembly from the mounting bracket. Do not disconnect the refrigerant line hoses from the compressor. Suspend the air...

Oil pump — removal and installation
Removal and installation 1. Remove the oil pan assembly ( for more details, see the relevant section in this chapter ). 2. Disconnect and remove the oil pump drive chain cover as shown in the figure below (arrows). 3....

Engine oil cooler — removal and installation
Removal 1. Drain the coolant from the engine (for more details, see the relevant section in the chapter " Cooling system "). 2. Remove the intake manifold assembly (for more details, see the relevant section in the...

Oil separator — removal and installation
Removal 1. Remove the soundproofing coating. 2. Unscrew the mounting screw (arrow) shown in the figure below, then remove and set aside the coolant recirculation pump. 3. Disconnect the crankcase ventilation hose (3)...

Engine oil pressure sensor
Removal Note: After removal, all elements of the thermal insulation coating must be installed in their original position. 1. Remove the soundproofing covering from the engine compartment. 2. Unscrew the mounting screws...

Engine oil pressure sensor (pressure relief line)
Removal 1. Pull and move the solenoid valve 1 of the fuel vapor recovery system activated carbon filter (3) away from the intake manifold, and then move it downwards. 2. Disconnect the wiring harness connector (2) shown...

Engine oil pressure check valve
Note: After removal, all elements of the thermal insulation coating must be installed in their original position. 1. Remove the soundproofing covering from the engine compartment. 2. Remove the thermal insulation...

Oil pump (2.0L engine)
Removal 1. Remove the lower part of the oil pan (for more details, see the relevant section in this chapter). 2. Unscrew the fastening screw (arrow) and remove the oil deflector plate shown in the figure below. 3. Using...

Upper Oil Pan (2.0 Engine) — removal and installation
Removal Note: The gearbox assembly must first be removed (for more details, see the relevant section in the chapter " Manual transmission / Automatic transmission "). 1. Remove the lower part of the oil pan ( for more...

Engine Oil Cooler (2.0L Engine) — removal and installation
Removal Note: Use extreme caution as the coolant in the system is under pressure. If the engine is hot, before starting work, it is necessary to relieve excess pressure by removing the expansion tank cap. 1. Drain the...

This section is available on russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

Read similar sections on other Skoda models

➧ Power unit: Lubrication system Skoda Fabia 1 (1999-2007)
➧ Power unit: Lubrication system Skoda Rapid 1 (2012-2022)

Link to this section in various formats

TEXTHTMLBB Code

Kodiaq 1 (2016-2024)