Car heating and air conditioning Skoda Kodiaq 1

Air conditioning system components
Air conditioning system components 1. Vents; 2. Air conditioning system humidity sensor; 3. Expansion valve; 4. Dryer body; 5. Ambient temperature sensor; 6. Capacitor; 7. Air conditioning compressor; 8. Valve for...

Heating and air conditioning system maintenance
Connecting a stand for servicing air conditioning systems for the purpose of measurement and testing Note: Depending on the type of tools selected, deviations may occur when performing work, so please see. operating...

Finding leaks in the refrigerant circuit using compressed air or nitrogen
Note: A relatively large leak can be detected, for example, by injecting purified and dried compressed air or nitrogen into the refrigerant circuit at a pressure of no more than 15 bar. If the leak is large enough, the...

Finding leaks in the refrigerant circuit using the VAG 1796 leak detector
Note: Minor leaks can be detected, for example, using an electronic detector. 1. Evacuate the refrigerant circuit using an air conditioning system servicing stand. Note: If a relatively large leak is detected during...

Finding leaks in the refrigerant circuit using the VAS 6196 kit or the VAS 6201 kit
Note: Minor leaks can be detected, for example, using an electronic detector. 1. Evacuate the refrigerant circuit using an air conditioning system servicing stand. Note: If a relatively large leak is detected during...

Purging the refrigerant circuit
Note: For vehicles where adapters cannot be connected to the refrigerant pipes, use, for example, a pneumatic gun with a rubber nozzle to blow out individual components. In this case, you need to act very carefully so...

Flushing the vehicle's air conditioning system
Note: A specialized center is not designed to flush the air conditioning system, much less remove metal particles. Flushing the air conditioning system is necessary for: removing contaminants from polyalkylene glycol...

Replacing the air conditioning compressor lubricating oil
Draining lubricating oil Note: Draining and measuring the amount of lubricating oil from the air conditioning compressor is only possible after the latter has been removed from the vehicle. 1. Drain the lubricating oil...

Possible malfunctions of the refrigerant circuit
Note: The air conditioning system is working properly if the air coming out of the front panel vents is at a temperature of 7°C or lower. Climatronic system setting: "LO". Setting the air conditioning system: "AC ON";...

Operations to determine system failures
Checking by direct visual inspection and observation In the event of a failure or deviation from the normal functioning of the air conditioning system, certain external signs of malfunction occur. In this case, the...

Elements of the air conditioning system — precautions
General information and precautions for handling refrigerant 1. Refrigerant R-134a has high volatility. If a drop of refrigerant comes into contact with the skin, it may cause local frostbite. When working with...

Expansion valve — removal and installation
Removal Attention: Beware of frostbite! If there is any refrigerant left in the air conditioning circuit, it will escape. Before depressurizing the circulation circuit, pump out the refrigerant. If the refrigerant...

Capacitor — removal and installation
Attention: Beware of frostbite! If there is any refrigerant left in the air conditioning circuit, it will escape. Before depressurizing the circulation circuit, pump out the refrigerant. If the refrigerant circuit is...

Air conditioning compressor — removal and installation
Removal 1. Remove the soundproofing covering from the engine compartment. 2. If necessary, remove the front right wheel arch liner (for more details, see the corresponding section in the chapter " Body "). 3. Remove the...

Air conditioning compressor pulley
Note: Be extremely careful with the air conditioning compressor drive pulley. Prevent it from falling and getting damaged. Removal and installation Removal 1. Remove the accessory drive belt (for more details, see the...

Evaporator — removal and installation
1. Remove the heating and air conditioning system module assembly ( for more details, see the relevant section in this chapter ). 2. Remove the fresh air intake fan. 3. Remove the air intake flap shaft. 4. Unscrew the...

Heater and Air Conditioning Module Assembly — removal and installation
Removal 1. If necessary, remove the decorative engine cover assembly. 2. If necessary, remove the air filter housing assembly (for more details, see the corresponding section in the chapter " 1.4L petrol engine / 2.0L...

Cabin filter — description
The filter with an activated carbon insert continues to perform the functions of a cabin filter. But at the same time, it also filters gaseous harmful substances in the passing air, such as ozone, benzene, nitrogen...

Cabin filter — removal and installation
Removal 1. Disconnect the glove box supports (arrows A) on both sides, then lower the glove box until it stops in the direction of arrow B. 2. If necessary, remove the insulator. 3. Disconnect the cover (1) from the...

This section is available on russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

Read similar sections on other Skoda models

➧ Body and interior: Interior heating Skoda Fabia 1 (1999-2007)
➧ Body and interior: Heating and air conditioning Skoda Rapid 1 (2012-2022)
➧ Body and interior: Ventilation and air conditioning Skoda Octavia 3 (2013-2019)
➧ Body and interior: Heating and air conditioning Skoda Yeti (2009-2017)

Link to this section in various formats

TEXTHTMLBB Code

Kodiaq 1 (2016-2024)