Vehicle Security Systems Skoda Rapid 1

Description of the passive safety system
The airbag system provides driver and passenger protection in addition to the safety belts to reduce the risk and severity of injury by deploying and inflating the driver and passenger airbags, side airbags, and seat...

Precautions when working with the security system
1. Work on the airbag may be performed at least 3 minutes after setting the ignition key to the OFF position and disconnecting the wire from the minus terminal ("-") of the battery, except when performing a wiring...

Airbags — general view
1. Front passenger side impact sensor 2. Passenger side airbag 3. Side airbag type "curtain" 4. Passenger side accelerometer 5. Driver's side airbag 6. Side airbag type "curtain" 7. Driver side accelerometer 8. Driver's...

Replacing Airbag System Parts
Warning: Traffic accident involving activation (by turning on the starting device) airbag system modules. It is essential to replace the following parts with new original parts: Central control unit for the Air bag...

Electronic airbag control unit — description
The command to deploy the airbags comes from the SRS unit, which receives a signal from the front and side impact sensors. 1. DC-DC converter; is located in the power supply unit, contains a step-up/step-down converter...

Electronic airbag control unit — removal and installation
Warning: Do not change the original position of the electronic control unit of the passive restraint system while the unit is connected to the network and the ignition is on. Otherwise, spontaneous deployment of the...

Side impact sensor on the central body pillar — removal and installation
Warning. Do not connect electrified measuring devices to the airbag terminals. This may cause spontaneous activation of the squib and, as a result, serious injuries. Note. Repair of the passive safety system components...

Side impact sensor on the rear body pillar — removal and installation
Warning. Do not connect electrified measuring devices to the airbag terminals. This may cause spontaneous activation of the squib and, as a result, serious injuries. Note. Repair of the passive safety system components...

Front passenger airbag switch — removal and installation
Removal 1. Disconnect the negative terminal from the battery. 2. Remove the glove box assembly (see the corresponding section in the chapter Body ). 3. Disconnect the wiring harness connector from the passenger front...

Driver Front Airbag Module — Removal and Installation
Warning. Do not connect electrified measuring devices to the airbag terminals. This may cause spontaneous activation of the squib and, as a result, serious injuries. Attention. To avoid spontaneous activation of the...

Front passenger airbag module — removal and installation
Caution: Always store the passenger airbag module with the housing facing down and the decorative cover facing up after removal. Never store the airbag module with the cover facing down. Failure to do so may result in...

Side airbag — removal and installation
Removal 1. Remove the front seat assembly (see the relevant section in Chapter Body ). 2. Disconnect the seat back from the cushion. 3. Remove the seat back cover. 4. Disconnect the wiring harness connector (5) from the...

Side curtain airbags — removal and installation
Caution: Always store the airbag module with the housing facing down and the decorative cover facing up after removal. Never store the airbag module with the cover facing down. Failure to do so may result in serious...

Activation of non-deployed airbag modules and pretensioners
Attention. If the vehicle is to be scrapped, the airbags and seat belt pretensioners must be activated inside the vehicle. If the vehicle is to be used in the future and only the airbag modules need to be scrapped, they...

Disposal of airbag modules and pretensioners
Once activated, the airbag modules and seat belt pretensioners must be disposed of in accordance with current environmental protection legislation. To do this, proceed as follows: 1. The pyropatron is very hot after...

Front seat belts — removal and installation
Attention. Always after an accident, it is necessary to perform a complete technical check of the following elements of the passive safety system. Inertia seat belt tensioners. Seat belt locks (buckles). Seat belt...

Front Seat Belt Height Adjuster — Removal and Installation
Attention. Always after an accident, it is necessary to perform a complete technical check of the following elements of the passive safety system. Inertia seat belt tensioners. Seat belt locks (buckles). Seat belt...

Front Seat Belt Buckle — Removal and Installation
Attention. Always after an accident, it is necessary to perform a complete technical check of the following elements of the passive safety system. Inertia seat belt tensioners. Seat belt locks (buckles). Seat belt...

Front Seat Belt Buckle (modification) — Removal and Installation
Removal 1. Remove the front seat assembly (see the corresponding section in the chapter Body ). 2. Disconnect the under-seat wiring harness connector (1) as shown in the figure below. 3. Disconnect the wiring harness...

Rear Outer Seat Belt — Removal and Installation
1. Remove the rear seat cushion assembly (see the corresponding section in Chapter Body ). 2. Remove the rear seat back assembly (see the corresponding section in Chapter Body ). 3. Remove the upper part of the luggage...

Rear Seat Center Seat Belt — Removal and Installation
Removal 1. Remove the rear seat cushion assembly (see the relevant section in Chapter Body ). 2. Unscrew the mounting bolt (3) shown in the figure below. Tightening torque of the mounting bolt during installation: 40...

Checking the operation of the automatic retraction mechanism lock
The automatic belt retraction mechanism has two types of locking action. The first type of locking is activated if the belt begins to quickly pull out of the automatic retraction mechanism. 1. Pull the belt out of the...

Checking the technical condition of seat belts
Note: If the vehicle has been involved in a traffic accident, the technical condition of the driver's and passenger's seat belts of the vehicle is checked only to eliminate all existing defects. 1. Turn the ignition key...

This section is available on russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

Read similar sections on other Skoda models

➧ Body and interior: Security systems Skoda Kodiaq 1 (2016-2024)

Link to this section in various formats

TEXTHTMLBB Code

Rapid 1 (2012-2022)