Exterior (external body elements) Skoda Kodiaq 1

Precautions when working with car body parts
When removing or disassembling any part, be careful not to damage or deform them. Parts that may interfere with the work must be covered with cloth. When removing parts using a screwdriver or other tool, protect the...

Front fender — removal and installation
1. Remove the front wheel arch liner ( for more details, see the relevant section in this chapter ). 2. Remove the front bumper panel assembly ( for more details, see the relevant section in this chapter ). 3. Remove...

Hood cover — removal and installation
Removal 1. Remove the washer jets. 2. Disconnect all wiring harness connectors (depending on the vehicle's configuration). 3. Loosen the fastening nuts (1) on the left and right sides to the hood hinges (2) (do not...

Hood Lock — removal and installation
Removal 1. Open the hood. 2. Disconnect the wiring harness connector. 3. Unscrew the mounting bolts (2) shown in the figure below 4. Disconnect the Bowden cable from the mounting bracket. 5. Pull and remove the hood...

Front bumper — removal and installation
Note: Depending on the modification, bumpers may differ. The bumper is removed together with the radiator grille. The wheel arch panel only needs to be detached from the mounting elements. Complete removal is not...

Rear bumper — removal and installation
Removal 1. Remove the rear lights (for more details, see the corresponding section in the chapter " Electrical equipment and systems of the car "). 2. Partially detach the front fender panel. 3. Unscrew the mounting...

Outside rearview mirror
Removal and installation the mirror assembly Removal 1. Remove the front door trim panel (for more details, see the relevant section in this chapter). 2. Disconnect the connector (4) of the wiring harness (3) of the...

Sunroof assembly
General appearance 1. Rear sunroof panel; 2. Fastening screw, tightening torque during installation 7 Nm; 3. Gasket; 4. Wiring harness; 5. Inner seal; 6. Rear section; 7. Curtain control module; 8. Fastening screw,...

Front wheel arch liner
Removal and installation 1. Remove the front wheel. 2. Unscrew the mounting screws (3) shown in the figure below. 3. Drill out the rivets (4). 4. Pull and remove the front wheel arch liner (1) as shown in the figure...

Body dimensions — body restoration work
Electrical components 1. Disconnect the negative battery terminal. 2. When disconnecting electrical connectors, do not pull on the wires, but hold on to the connector body. 3. When connecting, insert the connector until...

Body dimensions
Front of the body "a" = 1153 mm ±2.0 mm; "b" = 1412 mm ±2.0 mm; "c" = 1423 mm ±2.0 mm; "d" = 1072 mm ±2.0 mm; "e" = 879 mm ±2.0 mm Central part "a" = 1542 mm ±2.0 mm; "b" = 1582 mm ±2.0 mm; "c" = 1559 mm ±2.0 mm "a" =...

This section is available on russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

Read similar sections on other Skoda models

➧ Body and interior: Exterior (external elements) Skoda Fabia 2 (2007-2014)
➧ Body and interior: Exterior (external elements) Skoda Rapid 1 (2012-2022)
➧ Body and interior: Exterior (external elements) Skoda Octavia 3 (2013-2019)
➧ Body and interior: Exterior (external elements) Skoda Superb 2 (2008-2015)
➧ Body and interior: Exterior (external elements) Skoda Yeti (2009-2017)
➧ Body and interior: Exterior (external elements) Skoda Felicia (1994-2001)

Link to this section in various formats

TEXTHTMLBB Code

Kodiaq 1 (2016-2024)