Cooling system (petrol 2.0 l) of car Skoda Kodiaq 1

Replacing the coolant
Note: If the coolant is to be reused, it must be drained into a clean container prepared in advance. 1. Open the coolant expansion tank cap (arrow) as shown in the figure below. 2. Remove the soundproofing coating. 3....

Water pump assembly
Components 1. Fitting; 2. Sealing ring; 3. Mounting pin; 4. Fastening screw, tightening torque during installation 9 Nm; 5. Gasket; 6. Water pump; 7. Fastening screw, tightening torque during installation 9 Nm; 8....

Coolant recirculation pump
General appearance 1. Water hose; 2. Shut-off valve; 3. Coolant recirculation pump; 4. Support; 5. Mounting bolt, tightening torque during installation 20 Nm; 6. Clamp; 7. Water hose; 8. Water hose; 9. Fastening screw,...

Cooling system valve for gearbox
Cooling system valve for gearbox 1. Fastening screw, tightening torque during installation 9 Nm; 2. Water hose; 3. Fastening screw, tightening torque during installation 9 Nm; 4. Water hose; 5. Cooling system valve for...

Coolant temperature sensor
Coolant temperature sensor 1. Locking clamp; 2. Sealing ring; 3. Coolant temperature sensor at the radiator outlet; 4. Wiring harness connector; 5. Coolant temperature sensor; 6. Sealing ring; 7. Fastening screw,...

Water pump drive belt — removal and installation
Removal 1. Drain the coolant into a prepared container ( for more details, see the relevant section in this chapter ). 2. Remove the air filter housing (for more details, see the relevant section in the chapter " Intake...

Water pump — removal and installation
Removal 1. Drain the coolant from the engine cooling system ( for more details, see the relevant section in this chapter ). 2. Remove the air filter housing assembly (for more details, see the corresponding section in...

Coolant recirculation pump — removal and installation
Removal Note: When installing, all thermal insulation material must be installed in its original position. Attention: When the engine is warmed up to normal operating temperature, the coolant is under excess pressure....

Shut-off valve — removal and installation
Removal 1. Remove the air filter housing assembly (for more details, see the relevant section in the chapter " Intake and exhaust system "). 2. Release the fastening clamp (2) shown in the figure below. 3. Unscrew the...

Cylinder head cooling system valve — removal and installation
Removal 1. Remove the soundproofing coating. 2. Remove the air filter housing assembly (for more details, see the corresponding section in the chapter " Intake and exhaust system "). 3. Release the wiring harnesses (1)...

Engine Temperature Regulator Housing — removal and installation
Removal 1. Remove the water pump assembly ( for more details, see the relevant section in this chapter ). 2. Remove the throttle module assembly (for more details, see the relevant section in the chapter " Engine power...

This section is available on russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

Read similar sections on other Skoda models

➧ Petrol engines 1.4 l: Cooling and lubrication system Skoda Fabia 2 (2007-2014)
➧ Power unit: Cooling system Skoda Rapid 1 (2012-2022)
➧ Petrol engines 1.2 l: Cooling system Skoda Octavia 3 (2013-2019)
➧ Power unit: Cooling system Skoda Superb 2 (2008-2015)
➧ Power unit: Cooling system Skoda Yeti (2009-2017)
➧ Power unit: Cooling and heating Skoda Favorit (1987-1994)

Link to this section in various formats

TEXTHTMLBB Code

Kodiaq 1 (2016-2024)