The manual transmission code is indicated on the vehicle data sticker (see Introduction). Designation (For example, "02Q", 2 in illustrations 1.1 a, d, e), code and release date (see illustrations 1.1 b-e) The manual transmission is additionally indicated on the manual transmission itself. The code and date of issue is an alphanumeric sequence, for example, "LHX 14099". In this sequence "LHX" -identification code, "14" - day, "09" - month, and "9" - year (2009) transmission release.
1.1a Location of designation RKPP 0A4
1.1b Location of code and date of manufacture RKPP 0A4
1.1c Location code and production date OAJ manual transmission
1.1d Code with production date (1) and designation (2) Manual transmission 02Q
1.1e Code with production date (1) and designation (2) Manual transmission 02S
The gearbox is placed in a cast crankcase attached to the rear end of the cylinder block. The gearbox housing is equipped with holes for lowering, checking and adjusting the oil level, closed with screw plugs. Rotation on input (leading) the manual transmission shaft is transmitted from the engine crankshaft through the clutch assembly. The driven clutch disc is mounted on the splines of the input shaft. A schematic representation of the organization of torque transmission is shown in illustrations 1.2ad. The manual transmission 02Q uses two main gears: I - for gears from 1st to 4th, II - for 5th and 6th gears, as well as for reverse gear.
1.2a Schematic representation of the organization of torque transmission RKPP 0A4
Arrows - Direction of movement
1 engine
2 Clutch
3 RKPP
4 Input shaft
5 Output shaft
6 Differential
I-VI 1-6 gears
R Reverse gear
A Main gear
1.2b Schematic representation of the organization of torque transmission manual transmission OAJ
Arrows - Direction of movement
1 engine
2 Clutch
3 RKPP
4 Input shaft
5 Output shaft
6 Differential
I-VI 1-6 gears
R Reverse gear
A Main gear
1.2c Schematic representation of the organization of the transmission of torque Manual transmission 02Q AWD models
Arrows - Direction of movement
1 engine
2 Clutch
3 RKPP
4 Input shaft
5 Output shaft 5th, 6th and reverse gears
6 Output shaft 1st - 4th gear
7 Front differential
8 Corner drive
9 Cardan shaft
10 Haldex coupling
11 Rear final drive
12 Rear differential
I-VI 1-6 gears
R Reverse gear
A Front final drive
W1 Front corner gear
W2 Reverse corner gear
1.2d Code with production date (1) and designation (2) Manual transmission 02S
Arrows - Direction of movement
1 engine
2 Clutch
3 RKPP
4 Input shaft
5 Output shaft
6 Differential
I-VI 1-6 gears
R Reverse gear
A Main gear
Gear shifting is carried out by means of a gear lever located on the center console, via cable drives (see illustrations 1.3a-c).
1.3a Organization of the gear shift drive on models with manual transmission 02S (on 0A4 - similarly)
Arrow A Move gear selection
Arrow B Move slot selection
A Gear selector cable
B Groove selection cable
With heat shield
1 gear selector (selector)
2 Groove selection lever
1.3b Organization of the gear shift drive on models with manual transmission 0A4
Arrow A Move gear selection
Arrow B Move slot selection
A Gear selector cable
B Groove selection cable
C Heat shield
1 gear selector (selector)
2 Groove selection lever
1.3c Organization of gear shift drive on models with manual transmission 02Q
Arrow A Move gear selection
Arrow B Move slot selection
A Gear selector cable
B Groove selection cable
With heat shield
1 gear selector (selector)
2 Groove selection lever