Exterior (external body parts) Skoda Rapid 1

Hood — appearance
1. Front seal 2. Plug 3. Adjustment buffer 4. Hood lid lock bracket 5. Internal soundproofing lining of the bonnet lid 6. Travel limiter 7. Adjustment buffer 8. Plug 9. Canopy 10. Windshield washer nozzle 11. Support...

Removal and installation the hood cover
Removal 1. Remove the windshield washer system nozzles (5) shown in the figure below from the bonnet. 2. Disconnect the cable (4) from the front of the hood (1) as shown in the figure below. 3. Pass the cable (4)...

Removal and installation hood hinges
Removal 1. Remove the hood cover assembly (3) (see the relevant section in this chapter). 2. Unscrew the mounting bolts (2) shown in the figure below. The tightening torque of the mounting bolts during installation is...

Removal and installation the hood lock
Removal Note: The Bowden cable (2) does not disconnect from the hood latch. 1. Open the front hood. 2. Disconnect the Bowden cable (2) located in the cable bushing as shown in the figure below. 3. Disconnect the hood...

Removal and installation the hood release lever
1. Mounting bracket 2. Bowden cable 3. Adjusting nut 4. Fastening screw 5. Bonnet lid release handle Removal 1. Pull the bonnet release lever (1) towards you to open the bonnet. 2. Insert a flat-head screwdriver into...

Adjusting the bonnet lid
Note. The car must be parked on a flat, horizontal surface. The adjusting buffers (2) on the right and left sides of the bonnet are not used for adjustment. They are designed to stabilize or dampen the bonnet. The hood...

Luggage compartment door-appearance
1. Fastening screw 2. Buffer 3. Trunk lid trim panel 4. Luggage compartment door 5. Rubber buffer 6. Ball joint, tightening torque during installation 20 Nm 7. Gas-filled tailgate pillar

Removal and installation the tailgate
Removal 1. Remove the tailgate trim panel assembly (for more details, see the relevant section in this chapter). 2. Disconnect the wiring harness connectors from the electrical consumers in the luggage compartment door....

Adjusting the tailgate
Note. The car must be parked on a flat, horizontal surface. The tailgate lock is fixed inside the tailgate housing, so it is not adjustable. The buffers on the right and left sides of the luggage compartment door are...

Adjusting the trunk lid lock rod
Note. The trunk lid lock rod can be adjusted by means of enlarged holes for the mounting bolts in the horizontal and vertical directions. The rod must be adjusted so that it is centered in the recess in the door for the...

Removal and installation the tailgate lock
Removal 1. Remove the tailgate lock decorative cover (3) shown in the figure below. 2. Disconnect the wiring harness connector from the tailgate lock control (1) as shown in the figure below. 3. Loosen the mounting nuts...

Mudguards — removal and installation
Front wheel arch liner Removal 1. Unscrew the mounting bolts and remove the front wheel assembly. 2. Unscrew the fastening screws (3) shown in the figure below. 3. Pull down the front wheel arch liner (1) as shown in...

Outside rear view mirror — external appearance
1. Fastening screw, tightening torque during installation 1 Nm 2. Mirror position adjustment mechanism 3. Outside rearview mirror housing 4. Fastening screw 5. Outside rearview mirror support bracket 6. Mirror holder...

Removal and installation the outside rearview mirror
Caution: Wear protective gloves and safety glasses before starting work. Removal 1. Apply protective tape around the perimeter of the mirror housing to prevent damage to the paintwork. 2. Set the mirror to the extreme...

Removal and installation the exterior rearview mirror housing assembly
Removal 1. Remove the mirror from the holder (for more details, see the relevant section in this chapter). 2. Unlock the clamps by pressing them (arrows) as shown in the figure below. 3. Remove the mirror housing from...

Removal and installation the outside rearview mirror frame
Removal 1. Remove the mirror housing assembly. 2. Unlock the clamps on the back side. 3. Unlock the clamps from the front. 4. Remove the mirror frame from the support bracket assembly. Installation Installation is...

Removal and installation the exterior rearview mirror assembly
Removal 1. Remove the front door trim panel assembly (for more details, see the relevant section in this chapter). 2. Disconnect the wiring harness connector (2) of the wiring line (3) for controlling the outside...

Front bumper — appearance
1. mounting bolts, tightening torque during installation 2 Nm 2. Mounting screws 3. Front bumper assembly

Removal and installation the front bumper
Removal 1. Unscrew the screws securing the front part of the front wheel arch liner. 2. Unscrew the fastening screws (1) shown in the figure below. Tightening torque during installation 1.5 Nm. 3. Unscrew the fastening...

Front bumper beam — appearance
1. Front bumper beam 2. Fastening screw, tightening torque during installation 8 Nm 3. Fastening screw, tightening torque during installation 20 Nm

Rear bumper — appearance
1. Central section of the guide 2. Fastening nuts. Tightening torque during installation 2.2 Nm 3. Fastening nuts. Tightening torque during installation 2.2 Nm 4. Rear bumper beam assembly 5. Fastening screw, tightening...

Removal and installation the rear bumper
Removal 1. Remove the rear lights as an assembly (for more details, see the relevant section in the chapter Electrical equipment and electrical systems ). 2. Unscrew the mounting screws (4) from the inside of the wheel...

Rear bumper assembly (Spaceback) — appearance
1. Sleeve for mounting screw 2. Side section of the rear bumper guide 3. Fastening screw, tightening torque during installation 2.2 Nm 4. Rear part of the rear bumper guide 5. Fastening nut, tightening torque during...

Body dimensions of the front part of the body
Size a = 866 mm ±2.0 mm Size a= 1303 mm ±2.0 mm Size a = 1352 mm ±2.0 mm

Body dimensions of the central part of the body
Size a = 1184 mm ±2.0 mm Size b = 1184 mm ±2.0 mm Size a = 872 mm ±2.0 mm Size b = 1397 mm ±2.0 mm Size a = 1373 mm ±2.0 mm Size a = 1376 mm ±2.0 mm Size a = 1352 mm ±2.0 mm Size a = 1122 mm ±2.0 mm

Body dimensions of the rear part of the body
Size a = 1042 mm ±2.0 mm Rear of the body (Spaceback) Size a = 1056 mm ±2.0 mm Size b = 1318 mm ±2.0 mm Size c = 1109 mm ±2.0 mm Size d = 1185 mm ±2.0 mm Dimension e = 1057 mm ±2.0 mm

Body dimensions of the body bottom
Front part Size a = 619 mm ±2.0 mm Size b = 619 mm ±2.0 mm Size c = 953 mm ±2.0 mm Size a = 530 mm ±2.0 mm Dimension b = 576 mm ±2.0 mm Central part Size a = 1388 mm ±2.0 mm Rear end Size a = 946 mm ±2.0 mm Size b =...

This section is available on russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

Read similar sections on other Skoda models

➧ Body and interior: Exterior (external elements) Skoda Fabia 2 (2007-2014)
➧ Body and interior: Exterior (external elements) Skoda Octavia 1 (1996-2004)
➧ Body and interior: Exterior (external elements) Skoda Superb 2 (2008-2015)
➧ Body and interior: Exterior (external elements) Skoda Kodiaq 1 (2016-2024)
➧ Body and interior: Exterior (external elements) Skoda Yeti (2009-2017)
➧ Body and interior: Exterior (external elements) Skoda Felicia (1994-2001)

Link to this section in various formats

TEXTHTMLBB Code

Rapid 1 (2012-2022)