Doors, locks and windows of the car Skoda Rapid 1

Front doors assembly — external view
1. Front door assembly 2. Fastening bolt, tightening torque during installation 32 Nm 3. Front door canopy 4. Fastening screw, tightening torque during installation 23 Nm 5. Fastening bolt, tightening torque during...

Removal and installation the door assembly
Removal 1. Remove the dust boots (2) by squeezing the clips (arrow) and detaching the dust boot from the front body pillar, as shown in the figure below 2. Move the lever (3) downwards (arrow b) and disconnect the...

Adjusting the position of the front door
Note. Place the vehicle on a level, horizontal surface. The door is adjusted properly if it opens and closes without excessive force, and if there is an even gap around its perimeter with the door opening, if the door...

Front Door Elements — External View
1. Front door assembly 2. Mounting bracket 3. Mounting bracket cover 4. Lock cylinder cover 5. Support 6. Front door outer handle 7. Front door lock cylinder 8. Front door glass outer seal 9. Plug 10. Fastening screw,...

Removal and installation the door cover
Removal 1. Remove the front door trim panel assembly (for more details, see the relevant section in this chapter). 2. Lift the door cover (1) at the bottom as shown in the figure below. 3. Pull the cover downwards and...

Removal and installation the front door travel limiter
Removal 1. Remove the audio system speaker. 2. Unscrew the fastening screw (2) of the front body pillar. 3. Unscrew the mounting screws (3) and remove the front door travel limiter through the hole for the audio system...

Front door handle and lock — external view
1. Door lock assembly 2. Fastening screw, tightening torque during installation 3.5 Nm 3. Mounting bracket 4. Door lock cylinder 5. Support 6. Lid 7. Door handle 8. Fastening screw, tightening torque during installation...

Removal and installation the front door lock cylinder cover
Removal Note: When removing the lock cylinder cover, do not turn the screwdriver and the lever together with it. 1. Remove the door handle. 2. Insert a flat-head screwdriver (3) into the hole at the bottom of the cover...

Removal and installation the front door lock cylinder
Removal Note: The lock cylinder is installed in the driver's door only. 1. Remove the plugs (4) and (6) shown in the figure below. 2. Unscrew the mounting bolt (5) as shown in the figure below. 3. Completely unscrew the...

Removal and installation the front door handle cover (without lock cylinder)
Removal 1. Remove the plug on the end of the door (2) as shown in the figure below. 2. Insert a special tool (T10389) approximately 55 mm long into the door through the service hole so that the end of the tool is under...

Removal and installation the front door handle
Removal 1. Remove the lock cylinder (if the door is the driver's door) or the pen cover (if the door is a passenger door) (for more details, see the relevant section in this chapter). 2. Move the door opening handle (1)...

Removal and installation the front door lock
Removal 1. Remove the front door trim panel assembly (for more details, see the relevant section in this chapter). 2. Remove the front door cover (for more details, see the relevant section in this chapter). 3. Remove...

Removal and installation the mounting bracket
Removal 1. Remove the front door trim panel (for more details, see the relevant section in this chapter). 2. Remove the door cover (for more details, see the relevant section in this chapter). 3. Remove the door lock...

Front door glass assembly
1. Front door glass assembly 2. Window lifter assembly 3. Fastening nuts, tightening torque during installation 18 Nm 4. Door assembly 5. Electric motor of the window lifter servo drive 6. Fastening screw, tightening...

Removal and installation front door glass
Removal 1. Remove the front door trim panel (for more details, see the relevant section in this chapter). 2. Remove the service hole plug (4) shown in the figure below. 3. Remove the front door cover (5) shown in the...

Removal and installation the electric motor of the window lifter servo drive
Removal 1. Remove the front door trim panel (for more details, see the relevant section in this chapter). 2. Fix the door glass using adhesive tape to prevent it from falling inside the door. 3. Disconnect the wiring...

Removal and installation the front door window lift mechanism
Removal 1. Remove the front door trim panel assembly (for more details, see the relevant section in this chapter). 2. Remove the front door glass assembly (for more details, see the relevant section in this chapter). 3....

Removal and installation the front door glass guide
Note: When removing the glass seal, avoid excessive bending or twisting. Note: Make sure that the outside rearview mirror and door glass seal are removed. 1. Remove the retaining clip (3) in the direction of arrow "c"...

Rear doors — exterior view
1. Rear door assembly 2. Fastening bolt, tightening torque during installation 32 Nm (these bolts must always be replaced after disassembly) 3. Door canopy 4. Fastening screw, tightening torque during installation 23 Nm...

Removal and installation the rear door assembly
Removal 1. Press on the clips (arrow a), disconnect from the front body pillar and remove the boot (2), shown in the figure below. 2. Move the lever (3) downwards (arrow b) and disconnect the wiring harness connector...

Adjusting the position of the rear door relative to the body
Note. Place the vehicle on a level, horizontal surface. The door is adjusted properly if it opens and closes without excessive force, and if there is an even gap around its perimeter with the door opening, if the door...

Rear Door Interior — Exterior
1. Rear door assembly 2. Mounting bracket cover 3. Mounting bracket 4. Handle support 5. External door handle 6. Lid 7. Fastening screw, tightening torque during installation 8 Nm 8. Fastening nut, tightening torque 6...

Removal and installation the rear door cover
Removal 1. Remove the rear door trim panel assembly (for more details, see the relevant section in this chapter). 2. Lift the door cover at the bottom (1) as shown in the figure below. 3. Pull the door cover downwards...

Removal and installation the rear door travel limiter
Removal 1. Remove the audio system speaker. 2. Unscrew the screws (2) securing the door travel limiter to the front body pillar, as shown in the figure below. 3. Unscrew the mounting screws (3) and detach the travel...

Rear door handle and lock
1. Rear door lock 2. Cable (from internal control to lock (unlocking)) 3. Cable (from door lock to mounting bracket) 4. Mounting bracket 5. Fastening screw, tightening torque during installation 1.7 Nm 6. Door handle 7....

Removal and installation the rear handle cover
Removal 1. Remove the plug (2) from the rear door housing as shown in the figure below. 2. Install the special tool (T10389) into the door, approximately 38 mm, so that the end of the tool is under the locking hooks (3)...

Removal and installation the rear door handle
Removal 1. Remove the handle cover (for more details, see the relevant section in this chapter). 2. Move the door opening handle (1) carefully towards the rear of the vehicle (arrow a) to detach it from the mounting...

Removal and installation the rear door lock
Removal 1. Remove the rear door trim panel (for more details, see the relevant section in this chapter). 2. Remove the rear door cover (for more details, see the relevant section in this chapter). 3. Unscrew the...

Removal and installation the rear door mounting bracket
Removal 1. Remove the rear door trim panel assembly (for more details, see the relevant section in this chapter). 2. Remove the door cover (for more details, see the relevant section in this chapter). 3. Remove the...

Rear door glass assembly
1. Rear door glass assembly 2. Rear door glass guide 3. Fixed rear door glass 4. Rear door window lift mechanism assembly 5. Fastening nuts, tightening torque during installation 6 Nm 6. Fastening screws. Tightening...

Removal and installation rear door glass
Removal 1. Remove the rear door trim panel (for more details, see the relevant section in this chapter). 2. Remove the inner rear door seal. 3. Remove the cover (5) shown in the figure below. 4. Lower the rear door...

Removal and installation the electric motor of the rear door window lifter servo
Removal 1. Remove the rear door trim panel (for more details, see the relevant section in this chapter). 2. Fix the door glass using pieces of adhesive tape. 3. Disconnect the wiring harness connector (4) shown in the...

Removal and installation the rear door window lift drive (in case of a mechanical drive)
Removal 1. Remove the rear door window lift handle. 2. Remove the rear door trim panel (for more details, see the relevant section in this chapter). 3. Fix the rear door glass with adhesive tape. 4. Unscrew the...

Removal and installation the rear door window lift mechanism
Removal 1. Remove the rear door trim panel (for more details, see the relevant section in this chapter). 2. Remove the rear door glass (for more details, see the relevant section in this chapter). 3. Remove the rear...

Removal and installation the rear door glass guide channel
Removal 1. Disconnect the rear door glass guide seal (1) from the inside of the door frame as shown in the figure below. 2. Remove the guide (1) from the supports in the door (arrow b) as shown in the figure below. 3....

Removal and installation fixed rear door glass
Removal 1. Remove the rear door glass assembly (for more details, see the relevant section in this chapter). 2. Remove the outer seal. 3. Remove the protective film from the bolts (2) shown in the figure below. 4....

Removal and installation a fixed rear door glass (Spaceback option)
Removal 1. Remove the rear door glass (for more details, see the relevant section in this chapter). 2. Remove the outer seal. 3. Remove the protective film from the mounting bolt (3) shown in the figure below. 4....

Panoramic roof with sunroof — exterior
1. Panoramic roof glass 2. Sealing material 3. Perimeter gasket 4. Profile of the metal part of the roof 5. Mounting bolts

Removal and installation a panoramic roof
Removal Note. Before starting work related to the removal or installation of panoramic roof glass (cutting through adhesive joints using special strings), it is necessary to use protective glasses and gloves. Once...

Windshield — appearance
1. Windshield 2. Adhesive sealing material (PUR) (width = 6.5 mm, height a = 10 mm) 3. Body flange 4. The gap between the glass and the front body pillar (should be 2.5±0.5 mm) 5. The gap between the windshield and the...

Removal and installation the windshield
Removal 1. Remove the front pillar trim panel (on both sides) (for more details, see the relevant section in this chapter). 2. Remove both sun visors. 3. Remove the interior rearview mirror. 4. The roof trim panel must...

Rear window — exterior view
1. Rear glass assembly 2. Adhesive sealing material (PUR) (width - 6.5 mm, height a = 10 mm) 3. Body panel flange 4. Intermediate holder 5. Tailgate panel 6. Rear window regulator assembly 7. Installation location of...

Removal and installation the rear window
Removal Note: Wear protective gloves and safety glasses before starting work. Removal damaged glass 1. Place protective covering on interior elements to protect them from possible rear window fragments. 2. Remove the...

Rear window (Spaceback) — appearance
1. Height-adjusting buffer 2. Rear glass assembly 3. Body panel profiles

Removal and installation the rear window (Spaceback)
Attention: Before starting any work related to the removal and installation of the rear window, it is necessary to put on protective gloves and safety glasses. Removal damaged glass 1. Cover the car interior trim panels...

Preparing glass for installation on a car
With a layer of glue applied Note: Cut the glass adhesive layer to a thickness of 1-2 mm to apply fresh adhesive. When performing this operation, be extremely careful not to damage the glass surface. Attention. Do not...

Preparing the body opening for glass installation
Cut off the adhesive layer from the body opening using a special knife. as shown in the picture below. Do not completely remove the adhesive from the body under any circumstances. Note: The adhesive layer on the body...

This section is available on russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

Read similar sections on other Skoda models

➧ Body and interior: Doors, locks and windows Skoda Octavia 1 (1996-2004)
➧ Body and interior: Doors, locks and windows Skoda Kodiaq 1 (2016-2024)
➧ Body and interior: Doors, locks and windows Skoda Felicia (1994-2001)

Link to this section in various formats

TEXTHTMLBB Code

Rapid 1 (2012-2022)