General information about the car body The body of Skoda Octavia cars is load-bearing, with a steel frame, consists of two compartments. The rear part, extended under the rear window - with a stepped back - sedan type. The luggage compartment lid leans back...
Bearing part of the body — frame The frame is the main load-bearing part of the body and, thus, the entire Skoda Octavia. Therefore, the production number of the frame is included in the vehicle identification number. Not only other body parts are hung...
Front fenders Front fender The front fender is sheet-forged without any welded parts. The fenders are mounted during pre-assembly before body painting. Each wing is attached to the frame with nine bolts. The bolt holes in the fenders...
Plastic fender liner Front plastic fender mount Numbers in squares: 1 - self-tapping bolt; 2 - union nut; 3 - expansion nut; 4 - fender liner; 5 - front wing; 6 - front bumper Numbers in circles (attachment points): 1, 2 – front bumper; 3,...
Engine cover (hood) Sealing and gluing mastic on the cover of the engine compartment - hood 1 - outer sheet of the hood; 2 - inner sheet of the hood; 3 - edge gluing; 4 - wall facing the gap; 5 - adhesive and sealing mastic Mounting the...
Dividing wall trim Installing the plastic cover of the dividing wall 1 - casing of the separating partition; 2 - sealing of the separating partition; 3 - plastic clip; 4 - windshield; 5 - front cross member; 6 - protective film The pad is...
External rear view mirror Mounting the outside rear-view mirror 1 - sealing lining; 2 – an internal casing of a mirror; 3 - input; 4 - piston; 5 – control casing; 6 – an external rear-view mirror; 7 - electrical control; 8 - manual control; 9 -...
Mirrors with manual adjustment The position of the mirror is set manually from the cab of the car with a handle. The handle, pulled out of the plastic lining inside the door handle, is part of the transmission mechanism, inserted with a spike into...
Mirrors with electric position control and electric heating These mirror caps are made in the color of the car. In case of damage, the mirror cover can be removed by loosening the two bolts and pulling up and replaced with another one. The bolts can be accessed from the...
Third brake light Lantern of the third - additional brake light 1 – a lantern of the third stoplight; 2 - connecting package The third brake light on Skoda Octavia cars is installed as a special vehicle equipment. Flashlight (homological...
Roof side trims Fitting the roof side trim 1 - overlay assembly; 2 - clamps; 3 - rear tip; 4 - front tip; 5 - covers; 6 - lining ending; 7 - roof rack holder; 8 - nut; 9 - gasket; 10 - seal At the junction of the forgings of the roof,...
The front wall of the body, assy Welded front wall 1 - radiator bracket (used only when mounting a small radiator); 2 - front wall The front wall of the body is structurally solved in general differently from all previous types of Skoda cars - it is an...
Engine compartment lid lock (bonnet) Installation of the lock and fuse of the engine compartment cover 1 - engine compartment cover lock; 2 - control rod of the lock fuse; 3 - thrust (cable in a flexible sheath) castle; 4 - front wall (middle part) Lock of...
Front bumper — design description Assembling the front bumper and headlights 1 - headlight; 2 - bumper; 3 - spoiler; 4 - bumper frame; 5 - temperature sensor; 6 – temperature sensor bracket; 7 - nut Installing the front bumper and trim strip 1 - lining...
Assembly diagram of the complete module of the front wall of the body 1 - buffer overlay; 2 - bumper; 3 - front wall of the body (must be mounted without pretensioning); 4 - a screw with a six-sided head; 5 - screw; 6 - screw with a six-sided head; 7 - ventilation grille; 8 - hex head...
Replacing the front wall of the body Attention! It is not necessary to separate the coolant circulation circuit for engine cooling and the cooling circuit of the air conditioner, if the radiator and condenser are properly fixed to the engine. Disassembly...
Disassembly and assembly of the front wing Front fender 1. Disassemble the front bumper. 2. Remove the wheel arch insert (wings). 3. Remove the front turn signal lamp and side turn signal repeater. 4. Unscrew the fastening screws 2 of the body front panel module...
Assembly diagram of the engine hood Assembly diagram of the engine hood 1 – facing of a radiator; 2 - mounting angle; 3 - engine hood; 4 - a screw with a six-sided head; 5 - screw "Torx"; 6 - screws with hexagonal heads; 7 - hex head screw Adjustment can...
Assembly diagram of the front bumper Assembly diagram of the bumper 1 - bumper; 2 - screw "Torx"; 3 - front wall of the body; 4 - screw "Torx" (attaches wheel arch liner (wings)); 5 - nut; 6 - hex head screw (access to it opens as a result of removing the...
Assembly diagram of the rear bumper Assembly diagram of the rear bumper 1 - cross member (deformable part); 2 - hex nut; 3 – naschelnik under a back dimensional lantern; 4 - 1 Nm; 5 - flashing (pressed into the bumper clamps); 6 - bumper; 8 - buffer...
Assembly diagram of the exterior rear-view mirror Attention! When installing the mirror, press only on the middle of the glass. It is absolutely necessary to wear protective gloves. 1 - casing (take off at right angle with the box (frame) doors); 2 - seal; 3 - 2 Nm; 4...
Fuel tank neck plug cover The fuel tank neck, coming out on the right side, is equipped with a plug, and that, in turn, is closed with a plastic module with a lid and a sealed rubber cuff that seals the neck in the body. The cover of the module,...
Anti-corrosion body protection Layers of anti-corrosion protection 1 - sheet; 2 – tricationic phosphate; 3 - cathophoretic primer; 4 - filler; 5 - cover varnish consisting of a pigment layer and a top colorless varnish For good maintenance of the...