Car automatic transmission Skoda Rapid 1

Technical specifications
Main technical characteristics of the robotic 7-speed gearbox Automatic 6-speed transmission

Replacing the transmission oil of a 7-speed gearbox
Caution: If transmission oil leaks are found during inspection of the gearbox, the gearbox may be faulty. 1. Raise the car on a lift. 2. Place a container under the gearbox oil pan to collect the transmission oil. 3....

Checking and filling with ATF fluid (6-speed gearbox)
Note. Make sure the vehicle is level. The selector lever is in position "P", leave the engine running in idle mode. The air conditioner and heater are turned off. The ATF fluid temperature must not exceed 30°C at the...

ATF fluid replacement (6-speed transmission)
Drain 1. Place a catch basin under the gearbox. 2. Unscrew the ATF fluid inspection screw (A). Caution: Wear protective glasses. 3. Disconnect the bypass pipe (C) (5mm Allen key), leave to drain the ATF fluid. 4....

Dual Clutch — Design (Robotized 7-speed Gearbox)
1. Thrust bearing 2. Retainer 3. Adjusting washer "SK1" 4. Adjusting washer "SK2" 5. Small release bearing "K2" 6. Double clutch assembly 7. Retaining ring 8. Hub 9. Retaining ring 10. Large release bearing "K1" 11....

Removal the double clutch (robotized 7-speed gearbox)
Note. Necessary special devices, control and measuring instruments, as well as auxiliary means: Assembly stand "MR9-101". Hook "3438". Puller "T10323" Push-button part "T10368". Puller "T10373". Push-button part...

Adjusting the positions of the bearings of the K1 and K2 clutches (old version of the 7-speed gearbox)
Note. Necessary special devices, control and measuring instruments, as well as auxiliary means: Installation device "T10374". Pattern ruler "T40100". Glue "AMV 195 KD1 01". Digital depth gauge. Note. The adjusting shim...

Adjusting the positions of the clutch release bearings «K1» and «K2» (new version of the 7-speed gearbox)
1. Adjusting washer for "K1" 2. Large clutch release fork "K1" 3. Hinge 4. Small clutch release bearing "K2" 5. Adjusting washer for "K2" 6. Guide bushing, upper part 7. Small clutch release fork "K2" 8. Ball joint 9....

Adjusting the clutch «K2» (7-speed gearbox)
Determine the size "A2" to calculate the adjusting washer for the clutch "K2". 1. Remove the large clutch release fork shown in the figure below. 2. Install the clutch release fork to the upper and lower portions of the...

Dual Clutch Installation (7-Speed Gearbox)
Note. Necessary special devices, control and measuring instruments, as well as auxiliary means: Puller "T10373". Puller "T10323". Push-button part "T10368". Push-button part "T10376". Glue "AMV 195 KD1 01". Do not...

Gear shift drive (7-speed gearbox)
Gear shift drive control In the positions of the preselector lever "S", "D", "R" and in the Tiptronic position the starter cannot be activated. At speeds over 5 km/h and when the selector lever is moved to the "N"...

Setting up a 7-speed gearbox
1. The selector lever should be moved to the "P" position. 2. Turn off the ignition. 3. Loosen the screw (arrow) shown in the figure below. Note: If the clamp screw (arrow) is loosened, it is absolutely necessary that...

Emergency release of the gearshift drive from the «P» position (7-speed gearbox)
The preselector lever locking solenoid "N110" locks the preselector lever in the "P" position. The preselector lever can only be moved from the "P" position when the ignition is on or the engine is running, the brake...

Mechatronics of 7-speed gearbox — external view
1. Screw, 10 Nm (3 pieces, M8x35) 2. Screw, 10 Nm (4 pieces, M8x90) 3. Mechatronics of manual gearbox "J743".

Mechatronics of 7-speed gearbox — removal and installation
Removal Note. Necessary special devices, control and measuring instruments, as well as auxiliary means: Mounting lever "T10407". Diagnostic, measuring and information system of the car "VAS". Receiving bath "VAS 6208"....

Removal a 7-speed gearbox
1. Move the selector lever to position "P". Note: Do not remove the key from the ignition. 2. Remove the upper engine cover. 3. Remove the air filter. 4. Remove the battery and battery holder. 5. Remove the waterproof...

Installation of 7-speed gearbox
1. Installation is carried out in the reverse order of actions, and the following instructions must be observed. Note. During assembly work, it is necessary to replace the self-locking nuts and screws. Replace the...

Tightening torques for 7-speed gearbox
Gearbox mount to 1.4 l/90 kW TSI engine. 1) The bolt is located on the starter connection side. 2) Screwed on from the engine side. Gearbox Bracket - Gearbox and Gearbox Bearing - Gearbox Bracket Bolt (1) tightening...

Removal and installation of a 6-speed gearbox
Removal 1. Disconnect the negative terminal from the battery. 2. Set the gearbox mode selector to position "P". 3. Remove the upper decorative engine cover. 4. Remove the air filter housing assembly (see the...

Tightening torques for 6-speed gearbox
Gearbox mount to 1.6 l/77 kW engine 1) The bolt that also holds the starter. Transmission console 1) Always replace bolts after disassembly. Torque converter Torque converter mounting nuts: 57 Nm.

This section is available on russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

Read similar sections on other Skoda models

➧ Transmission: Automatic gearbox 0CW Skoda Octavia 3 (2013-2019)
➧ Transmission: Automatic gearbox Skoda Kodiaq 1 (2016-2024)

Link to this section in various formats

TEXTHTMLBB Code

Rapid 1 (2012-2022)