Car engine lubrication system Skoda Rapid 1

Lubrication system components in assembly (1.2L MPI engine)
1. Engine oil pressure drop sensor (0.045 MPa), tightening torque when installing the sensor 25 Nm 2. Guide pins 3. Oil pump assembly 4. Oil pump mounting bolt, tightening torque during installation 24 Nm 5. Oil pan 6....

Oil filter — external view (1.2L MPI engine)
1. Threaded plug with holder of filter element of oil filter (25 Nm) 2. Seal 3. Oil filter element 4. Compaction 5. Bolt (24 Nm) 6. Oil filter housing 7. O-ring with circular cross-section

Oil filter — removal and installation (1.2L MPI engine)
1. Unscrew the screw plug to a height of (a) (arrow) (or 3 turns), leave it in this position for at least one minute to allow the oil to drain from the filter element. Note: If the threaded plug is completely removed...

Oil pan (1.2L MPI engine)
Removal 1. Remove the lower engine compartment covers (arrows). 2. Drain the engine oil. 3. Loosen the oil pan mounting screws. 4. Remove the oil pan: if necessary, loosen it by tapping it lightly with a rubber hammer....

Oil pump — removal and installation (1.2L MPI engine)
1. Remove the oil pan. 2. Loosen the screw (1), remove the oil pump chain casing (2) from the clamps at the section (arrow). 3. Unscrew the screw (2). 4. Move the oil pump drive chain tensioner (4) in the direction of...

Lubrication system components of the 1.2 l TSI engine in assembly
1. Oil filler cap 2. Pressure line of the lubrication system 3. Oil dipstick 4. Mounting bracket for attachments (upper) (with oil filter and oil cooler) 5. Gasket 6. Guide bushing 7. Oil filter assembly, tightening...

Oil pan — removal and installation (1.2L TSI engine)
Removal Note. Necessary special devices, control and measuring instruments, as well as auxiliary means: Socket wrench "T10058". Gasket Stripper (GST storage code, item no. R 34402), manufacturer Retech sro. Cleanser and...

Oil pump — removal and installation (1.2 l TSI engine)
Removal Note. Necessary special devices, control and measuring instruments, as well as auxiliary means: Container for collecting engine oil -WAS 6208-. 1. Remove the oil pan (for more details, see the relevant section...

Engine Oil Cooler — Removal and Installation (1.2L TSI Engine)
Note. Necessary devices, special control and measuring instruments, as well as auxiliary means: - Container for collecting engine oil. - Pliers for clamps. Removal 1. Drain the coolant For more details, see the relevant...

Checking the oil pressure and hydraulic oil pressure drop switch (1.2 l TSI engine)
Note. Necessary devices, special control and measuring instruments, as well as auxiliary means: Oil pressure tester, "V.A.G 1342". Voltage tester (semiconductor diode test lamp), "VAG 1527 B". Auxiliary measuring kit,...

Elements of the lubrication system of the 1.4 l TSI engine
1. Oil dipstick 2. Engine oil cooler 3. Sealing ring 4. Water pipe of the cooling system 5. Fastening bolt, tightening torque during installation 8 Nm + tighten by an additional 90° 6. Oil filler cap 7. Sealing ring 8....

Oil pan — removal and installation (1.4L TSI engine)
Note. Necessary special devices, control and measuring instruments, as well as auxiliary means. Socket wrench "T10058". Sealer removal tool "Gasket Stripper" (gST storage code item Nt R 34402). manufacturer Retech...

Oil pump — removal and installation (1.4 l TSI engine)
Note. Necessary special devices, control and measuring instruments, as well as auxiliary means: Clamping device "T10172". Removal 1. Remove the oil pan (for more details, see the relevant section in this chapter). 2....

Engine Oil Cooler (Radiator) — Removal and Installation (1.4L TSI Engine)
Removal 1. Drain the coolant from the engine cooling system (for more details, see the relevant section in the chapter Cooling system ). 2. Remove the alternator (for more details, see the relevant section in the...

Checking oil pressure and hydraulic oil pressure drop switch-sensor (1.4 l TSI engine)
Note. Necessary special devices, control and measuring instruments, as well as auxiliary means: Hinged wrench 24 "T40175". Test device for checking oil pressure. Voltage tester (semiconductor diode test lamp), -VAG 1527...

1.6L MPI Engine Lubrication System Assemblies
1. Oil dipstick 2. Double drive sprocket 3. Gasket 4. Valve timing chain housing 5. Sealing ring 6. Oil filler cap 7. Oil filter assembly 8. Fastening bolt, tightening torque 10 Nm 9. Fixing screw 10. Crankshaft pulley...

Oil pan — removal and installation (1.6L MPI engine)
Note. Necessary special devices, control and measuring instruments, as well as auxiliary means: Attachment tip "T10058". Gasket Stripper (GST storage code, item no. R 34402), manufacturer Retecti sro. Cleanser and...

Oil pump — removal and installation (1.6L MPI engine)
Removal 1. Remove the oil pan (for more details, see the relevant section in this chapter). 2. Remove the oil pump chain sprocket cover (A) shown in the figure below. 3. Hold the oil pump chain sprocket with the...

Checking the oil pressure and hydraulic oil pressure drop switch -F1- (1.6 l MPI engine)
Note. Necessary special devices, control and measuring instruments, as well as auxiliary means: Oil Pressure testing Device "V.A.G 1342". Voltage tester (semiconductor diode test lamp) "V.A.G 1527". Auxiliary measuring...

Lubrication system components of the 1.6 l TDI engine in assembly
1. Fastening bolt, tightening torque when installing the bolt 15 Nm 2. Crankshaft seal housing assembly 3. Toothed belt of oil pump drive 4. Screw for fastening the oil dipstick guide, tightening torque during...

Oil filter holder (1.6L TDI engine)
Appearance 1. Cover, tightening torque during installation 25 Nm 2. Sealing ring 3. Sealing ring 4. Sealing ring 5. Insert 6. Oil radiator/cooler 7. Fastening bolt, tightening torque during installation 11 Nm 8. Seal 9....

Oil filter assembly with holder and engine oil cooler — removal and installation (1.6L TDI engine)
Note. Necessary devices, special control and measuring instruments, as well as auxiliary means: Assembly tool "T10118". Container for collecting engine oil "VAS 6208". Tool for removing soft upholstery "MP8-602/1"....

Engine Oil Cooler — Removal and Installation (1.6L TDI Engine)
Removal 1. Drain the coolant for more information, see the relevant section in the Cooling System chapter). 2. Remove the air filter housing for more details, see the relevant section in the chapter Intake and Exhaust...

Engine Oil Pressure Drop Sensor — Removal and Installation (1.6L TDI Engine)
Removal 1. Remove the upper decorative engine cover. 2. Remove the engine crankcase ventilation hose (1), shown in the figure below, by pressing the release buttons. 3. Release the suction hoses (arrows) shown in the...

Turbocharger Oil Inlet and Outlet Pipe Assembly Diagram (1.6L TDI Engine)
1. Fastening bolt, tightening torque during installation 20 Nm 2. Fastening bolt, tightening torque during installation 22 Nm 3. Lubricating oil supply line 4. Drain lubrication line 5. Fastening bolt. Tightening torque...

Oil pan — removal and installation (1.6L TDI engine)
Removal Note. Necessary special devices, control and measuring instruments, as well as auxiliary means: Socket wrench "T10058". Device for catching and sucking out old oil "V.A.G 1782". Silicone sealing mastic "0 176...

Oil pump — removal and installation (1.6 l TDI engine)
Removal 1. Remove the oil pan (for more details, see the relevant section in this chapter). 2. Unscrew the mounting bolts (4) shown in the figure below, then remove the oil receiver assembly (3). 3. Unscrew the mounting...

This section is available on russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

Read similar sections on other Skoda models

➧ Power unit: Lubrication system Skoda Fabia 1 (1999-2007)
➧ Power unit: Lubrication system (petrol) Skoda Kodiaq 1 (2016-2024)

Link to this section in various formats

TEXTHTMLBB Code

Rapid 1 (2012-2022)