Shift drive control
In the positions of the selector lever «S», «D», «R» and in the Tiptronic position it is impossible for the starter to work.
At speeds above 5 km/h and moving the preselector lever to the position «N» the electromagnet for blocking the selector lever must not jump in, blocking the selector lever. Using the preselector lever, it is possible to turn on the running stage.
At speeds lower than 5 km/h (the car is almost worth it) and moving the preselector lever to the position «N» it is permissible that the electromagnet for blocking the selector lever jumps in only approx. after 1 s. Preselector lever can be moved out of position «N» only when the brake pedal is pressed.
Selector lever - in position «R», the button in the preselector lever is pressed and the ignition is on:
Brake pedal not pressed
The selector lever is locked when the button is pressed and it is impossible to move it from the position «R». The selector lever is blocked by an electromagnet to block the selector lever.
The selector lever lock solenoid no longer locks the selector lever. Travel gear selection is possible. Shift gears slowly with the selector lever «R» through «R», «N», «D», «S»; at the same time, check that the image of the position of the selector lever in the instrument panel corresponds to the actual position of the selector lever.
Selector lever - in position «N», the button in the preselector lever is pressed and the ignition is on:
Brake pedal not pressed
The selector lever is locked and cannot be moved out of position «N». The selector lever is blocked by an electromagnet to block the selector lever.
Brake pedal pressed
The selector lever lock solenoid no longer locks the selector lever. The choice of running stage is possible.
Note. Moving out of position «N» V «O» possible with the brake pedal depressed, also without pressing the button in the preselector lever. To move from position «N» V «R» you still need to press the button in the head of the preselector lever.
Selector lever - in position «D», ignition on
The selector lever is locked and cannot be moved from the position «D» into position «S».
The button in the preselector lever is pressed
The selector lever is released and it is possible to move it from the position «D» into position «S».
Selector lever - in position «D», ignition and headlights on
Moving the preselector lever to the Tiptronic track
Symbol highlight «0» when illuminated, the scale on the preselector lever -L101- must go out and the symbols must light up «+» And
As a result of moving into the Tiptronic track, the image of the preselector lever -Y6- in the instrument panel should change from «P RNDS» V «7 6 5 4 3 2 1».
Selector lever - in track for Tiptronic, shifting «+» and «-».
Image of the position of the selector lever «7 6 5 4 3 2 1» in the instrument panel, when moving the preselector lever to «+» and acc. change always one speed step up and down, resp.
If the shift actuator does not work as described
1. Check the cable tightening of the preselector lever and adjust it.
2. Check the safety device that prevents the key from being removed from the ignition switch.
Selector lever position indicator
If all segments of the image of the position of the selector lever are lit, this means that the gearbox is in emergency mode.
Control of the adjusted position of the cable tightening of the preselector lever
Note. The gearshift drive has been checked.
1. With the button pressed, move the preselector lever from the position «R» about 5 mm towards the back and hold it, but do not move it all the way to the position «R».
2. Release the preselector lever. The selector lever should spontaneously return to the position «R». Otherwise it is necessary to adjust the gearshift actuator.
3. Move the preselector lever to position «N».
4. With the button pressed, move the preselector lever from the position «N» about 5 mm towards the back and hold it, but do not move it all the way to the position «0».
5. Release the preselector lever. The selector lever should spontaneously return to the position «N». Otherwise it is necessary to adjust the gearshift actuator.
6. With the button pressed, move the preselector lever from the position «N» about 5 mm towards the back and hold it, but do not move it all the way to the position «R».
7. Release the preselector lever. The selector lever should spontaneously return to the position «N». Otherwise it is necessary to adjust the gearshift actuator.
Selector lever cable adjustment
Note.
- The cable tightening of the preselector lever must be adjusted if:
- The cable tightening of the preselector lever was removed from the gearbox.
- The engine or gearbox was removed and installed.
- The parts of the unit support were removed and installed.
- The cable tightening of the preselector lever or the gearshift drive was removed and installed.
- The position of the engine and gearbox has been changed, e.g. during installation without internal stresses.
1. Remove the air filter (see the relevant section in chapter Intake and exhaust system).
2. Make sure that the lock washer (arrow) correctly installed and fixed downwards as shown in the figure below.
Note. Safety cover (arrow) should be replaced after removal.
3. Move the selector lever out of «R» V «S».
4. Check the front protective cover of the gearshift drive on the cable tightening of the selector lever for damage. If it is damaged, the cable tightening of the selector lever must be replaced. The shift actuator and the selector lever cable must move slightly during gear changes. If this is not the case, then it is necessary to replace the cable tightening of the selector lever or repair the gear shift actuator.