Doors, locks and windows of the car Skoda Octavia 3

Front door hinge parts and assemblies
1. Door 2. Socket head screw: 40 Nm 3. Door hinge: the hinge is detachable; the upper part of the loop is connected to the lower part using screw "4" 4. Screw: To remove the door, this screw must be unscrewed from the...

Front door adjustment
Note: The car must be on wheels to adjust the door. The door is adjusted correctly if the gap is the same around the entire perimeter when closed, the door is not recessed or protruding. After installation or...

Front door parts and components
1. Door 2. Fixed nut 3. Sticky pad 4. External door seal 5. Lid 6. Inner glass groove seal 7. External glass groove seal 8. Foam piece 9. Glass guide Removal and installation the door cover Remove the front door trim....

Parts and assemblies of the front door handle and lock
1. Door lock 2. Screw: For lock cylinder. Tightening torque: 2.2 Nm. 3. Pen body 4. Lock cylinder: The lock cylinder is located only on the driver's door. 5. Lining 6. Cap: Various designs 7. Door handle: Different...

Removal and installation the cylinder and cylinder cover of the front door lock
Removal and installation the front door lock cylinder cover Note: When removing the protective cover of the lock cylinder, do not twist or pry the screwdriver with the screwdriver. Remove the door handle. Insert a thin...

Removal and installation the front door cover (without the lock cylinder)
Remove the plugs of the rear holes "3". Insert the device "T10389" approximately 55 mm into the door and hook it onto the latch "2" of the handle housing. Pull the device "T10389" back "arrow" so that the latch opens....

Removal and installation the front door handle and lock
Removal and installation the door handle Remove the lock cylinder or its cover. Pull the handle "1" back a little "arrow a" from the socket in the handle body. Move the handle along "arrow b". Holding the handle at a...

Removal and installation the front door handle housing
Remove the front door trim. Remove the door cover. Remove the lock cylinder or cover. Remove the outer door handle. Unscrew screw "4" and remove gasket "3". Remove handle housing "1" from door "arrow a". Disconnecting...

Front door glass — design description
1. Door glass 2. Window lifters 3. Nuts: 6 Nm 4. Door 5. Window lifter motor 6. Screw: 3 Nm 7. Glass guide: placed on the flange

Removal and installation front door glass
Remove the front door trim. Remove the inner door cavity sealing strip. Pry up and remove the plug "4". Remove the trim "5". Lower the glass "1" so that the locks "2" on the guide wheels "3" become visible in the holes....

Removal and installation the front door window lift motor
Remove the front door trim. Secure the window glass with adhesive tape so that it does not slide down. Disconnect the connector "4". Unscrew the screws "2". Remove the window lift motor together with the control unit...

Removal and installation the front door window lifter
Remove the front door trim. Remove the door glass. Remove the window lifter motor. Loosen the nuts "3". Unlock the cable reel locks -see arrows d- and push them into the door. Push the window lifter "1" into the door...

Removal and installation seals for the front door glass grooves
Removal and installation the internal glass groove seal Note: Remove the seal evenly, without bending, with an upward movement. Remove the front door trim. Evenly remove the seal "1" "arrow" from the door flanging "2"....

Removal and installation front door seals
Removal and installation the inner door seal During assembly at the factory, the internal door seals are coated with sealant, placed on the door frame flange and rolled with a roller. Note: When removing a seal, the...

Central lock
Note: The central locking servomotors for the front and rear doors are integral parts of the door lock and cannot be replaced separately. After replacing the door lock with the central locking servomotor, interrogate...

Rear door — design description, removal and installation
1. Door 2. Socket head screw: 40 Nm 3. Door hinge: the upper part of the hinge is connected to the lower part using screw "4"; the loop is detachable 4. Screw: To remove the door, this screw must be unscrewed from the...

Rear door adjustment
Note: To adjust the rear door, the car must be on its wheels. The rear door is adjusted correctly if the gap is the same around the entire perimeter when closed, the door is not recessed or protruding outward. Set the...

Rear door trims — design description
1. Door 2. Inner glass groove seal 3. Door gap seal 4. Fixed nuts 5. Cap 6. Lid 7. External door seal 8. Fixed glass with external seal 9. Glass guide

Removal and installation the rear door trim
Remove the door trim. Lift cover "3" at the bottom. Move cover "3" down and remove it from door "4" in the direction of the "arrow". Note: If necessary for further work, pull out cable "1" with sleeve "2" from cover...

Removal and installation the rear door opening limiter
Remove the door trim. Unscrew screw "2" on pillar B. Unscrew screws "3". Remove the plastic cover above the speaker and remove the door travel limiter "1". Installation Insert door travel limiter "1" into the hole...

Removal and installation the rear door lock bracket
Unscrew screws "2" and remove locking bracket "1". Installation Install the locking bracket "1" on the D-pillar and tighten the screws "2". Tightening torque: 25 Nm. Adjust the lock bracket.

Rear door handle and lock parts and assemblies
1. Pen body 2. Lining 3. Cap 4. Door handle 5. Screw: Tightening torque: 1.7 Nm. When this screw is removed, the door support bracket becomes loose. 6. Cable: From the door lock to the support bracket. 7. Door lock 8....

Removal and installation the rear door cover
Remove plugs "3" from the rear holes. Insert assembly tool "T10389" approx. 38 mm into the hole behind the locking hook "2" of the support bracket. Pull tool "T10389" back "arrow" until the latch opens. Pull the handle....

Removal and installation the rear door handle and lock
Removal and installation the door handle Remove the cover. Pull handle "1" back slightly "arrow a" from the socket in the handle housing. Move the handle along "arrow b". Remove the door handle at a right angle "arrow...

Removal and installation the rear door handle housing
Remove the rear door trim. Remove the cover. Remove the outer door handle. Unscrew screw "4" and remove gasket "3". Remove handle housing "1" from door "arrow a". Disconnecting the drive cable Unlock fastening "5" and,...

Rear Door Glass — Design Description
1. Door 2. Door glass 3. Glass guide: Installed on the flange 4. Fixed window glass 5. Notched pin and expansion dowel: For fixing the door glass 6. Screw: Tightening torque: 8 Nm 7. Nuts: Tightening torque: 7 Nm 8....

Removal and installation rear door glass
Remove the rear door trim. Remove the inner door seal. Pry up and remove the plug "5". Lower the door window "6" so that the spacer pin "4" and spacer insert "3" can be accessed through the window lifter cutout "2"....

Removal and installation the rear door window lift motor
Remove the door trim. Secure the window glass with adhesive tape so that it does not slide down. Disconnect the connector "4". Unscrew the screws "2". Remove the window lift motor with the ECU "1" from the mounts of the...

Removal and installation the manual rear door drive
Remove the window lift handle. Remove the door trim. Secure the window glass with adhesive tape so that it does not slide down. Unscrew the screws "2". Remove the mechanical drive "1" from the mounts of the coil with...

Removal and installation the rear door window lifter and its handle
Removal and installation the window lift handle Compress the locking ring "2" "arrow a". Slightly pull out the locking ring "2" under the window lifter handle (pos. 1) "arrow b". Remove the handle "1" "arrow c"....

Removal and installation the rear door glass guide
Note: Do not bend the glass guide when removing it! Remove the door trim. Remove the inner door cavity sealing strip. Lower the door glass to the lowest position. Disconnect the glass guide in the pillar cavity and...

Removal and installation the outer trim of the C-pillar
Partially remove the glass guide seal in places "3" on the inside of the door. Unscrew screws "3" (2 Nm). Partially remove the outer glass groove seal. Remove the outer trim of the C pillar "2" from the glass guide.

Removal and installation fixed rear door window glass
Remove the door glass. Remove the glass guide. Remove the inner sealing strip of the door cavity. Remove the protective film from the threaded hole "2". Unscrew the screw "2". Move the seal from the inside of the fixed...

Removal and installation the inner seal of the rear door glass groove
Remove the rear door trim. Evenly remove the seal "1" "arrow" from the door flanging "2". Installation Press seal "1" evenly onto flange "2" by hand. Removal and installation the outer glass groove seal (Combi) Note....

Removal and installation rear door seals
Removal and installation the rear door inner seal During assembly at the factory, the internal door seals are coated with sealant, placed on the door frame flange and rolled with a roller. Note: When removing the seal,...

Windshield parts
Caution! Reusing a cut-out windshield is not permitted for safety reasons. The windshield must only be replaced with a new original part. Cut-out rear and side windows can be reused, but only after careful inspection....

Rear window parts and components
1. Rear window 2. Polyurethane adhesive-sealant: Dimensions of the adhesive layer: width -b- = 6.5 mm, height "a" = 10 mm (including sealing profile, sealant residues on glass and glass flange). Minimum curing time. 3....

Side glass parts and units (Combi)
1. Sidewall 2. Guide pin: is a component of the side glass and is cut by a cutting wire when removed. 3. Sealing profile: is a component of the side glass 4. Side glass

Mudguards — removal and installation
Front mudguard Remove the wheel. Unscrew the screws "3" from the spacer inserts "2". Remove the mudguard "1" from the body "4". Installation Note: Check the expansion nuts "2" for damage and replace if necessary. Insert...

This section is available on russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

Read similar sections on other Skoda models

➧ Body and interior: Doors, locks and windows Skoda Rapid 1 (2012-2022)
➧ Body and interior: Doors, locks and windows Skoda Kodiaq 1 (2016-2024)
➧ Body and interior: Doors, locks and windows Skoda Felicia (1994-2001)

Link to this section in various formats

TEXTHTMLBB Code

Octavia 3 (2013-2019)