Electrical system specifications System Type - 12V Negative Ground Battery Capacity - 40 Ah Generator Type - PAL Kromeriz 443 113 516 631 Output current at a voltage of 14 V and 6000 rpm - 55 A Regulated voltage - 14.2 V maximum Voltage regulator - PAL...
General description and precautions 12 V electrical system with negative ground. Consists of battery, alternator, starter, electrical components and wiring. The starter has a freewheel with pre-engagement with the traction relay. When starting the engine,...
Troubleshooting in electrical circuits Note. Before starting work, see the precautions given in Head of this Section . The following checks only apply to main electrical circuits and should not be used on ELECTRONIC circuits. General description 1. The...
Fuses, relays and turn signal/alarm breaker Pic. 12.5. Location of components in the fuse and relay box - models 1989-1992 1. Fuses; 2. Relay - rear fog lights; 3. Relay - front fog lights; 4. Relay - dipped headlights; 5. Relay - spare; 6. Turnip - front wiper...
Switches — removal and installation Note: Disconnect the negative cable from the battery before removing the switch. Egnition lock 1. For details on removing and installing the switch, see Section 10 . Multifunction switches on the steering column...
Lamps (external lighting fixtures) — replacement General description 1. Whenever replacing lamps, please refer to the following points: a) Before starting work, turn off the relevant lights. b) Remember that if the lantern has just been lit, the lamp may be very hot....
Lamps (interior lighting) — replacement General description 1. Be guided Chapter 13, paragraph 1 . Before starting work, in the case of circuits that cannot be switched off (e.g. interior lighting), remove the appropriate fuse or disconnect the negative cable...
External lighting devices — removal and installation Warning: Before starting work, turn off the relevant lights. Headlight block Removing 1. Working in the engine compartment, disconnect the electrical wiring from the headlight and front turn signal (photo). 2....
Light Beam Direction Adjustment — General Description Pic. 12.7. Light Beam Direction Adjustment Diagram A - Headlight center distance B - Light/shadow border C - Center low beam D - Dipped beam spot H - Height from the ground to the center of the headlights O - Vehicle...
Headlight beam control system — general description 1. To compensate for the loading of the car, it is necessary to correct the direction of the light beam by turning the knob on the panel. 2. The system includes a control unit installed in the dashboard, a hydraulic...
Low beam system — general description Note: Low beam system is not installed on all models. 1. The low beam mode unit is installed on the upper support of the right suspension strut (photo), and controls the headlight circuit in such a way that when the...
Dashboard — removal and installation Removing 1. Disconnect the negative cable from the battery. 2. Remove the central and auxiliary switch panels ( Chapter 12 ). 3. Separate the lower trim panel of the casing of the instrument panel (photo). 4. Unscrew...
Instrument panel components — removal and installation General description 1. Remove the instrument panel ( Chapter 19 ), then proceed as described in the relevant subchapter. Devices Health check 2. When checking the coolant temperature gauge circuit, refer to Section 3 ....
Speedometer drive cable — removal and installation Removing 1. Remove the dashboard ( Chapter 19 ). 2. Unscrew the speedometer drive cable from the back of the dashboard, and pass the cable into the engine compartment (photo). 3. Working in the engine compartment,...
Sound signal — adjustment, removal and installation Adjustment 1. Turn the knob on the back of the horn a quarter of a turn at a time in either direction, and adjust the sound by ear (see photo 22.4). 2. After adjustment, block the adjuster screw with paint. Removing 3....
Rear window heater — general description 1. The rear glass is heated by a coil attached to the inside of the glass. 2. The heating element is very fragile, so the following precautions should be observed. a) Do not leave luggage or other items that may rub...
Fasten seat belt reminder system — general description Note: This system may not be available on all models. 1. When the ignition key is turned to position 1, a buzzer will sound for approximately five seconds to remind you to fasten your seat belt. 2. The system is powered...
Wiper arms — removal and installation Removing 1. Before removing the wiper arm, make sure the motor is in «parked» position. To check this, turn on the windshield wipers. and then turn off - the motor should automatically return the wipers to «parked»...
Wiper motor and rod — removal and installation Pic. 12.8. Wiper motor and rod 1. Bracket swivel adapter wiper; 2. Wiper blade; 3. Wiper arm; 4. Motor; 6. Mounting bracket for linkage and wiper motor; 7. Top rubber pad; 8. A nut of fastening of a screen wiper to a...
Rear wiper motor — removal and installation Removing 1. Remove rear door interior trim panel ( Section 11 ). 2. Disconnect the negative cable from the battery. 3. Remove the wiper arm and brush ( Chapter 25 ). 4. Loosen the spindle housing nut, then remove the...
Components of the windshield washer system — removal and installation Pic. 12.10. Components of the windshield washer system 1. Tank; 2. Filler cap; 3. An arm of fastening of a tank to a body; 4. Washer pump seal ring in the reservoir; 5. Rear windshield washer pump; 6. Windshield washer...
Car radio unit — removal and installation Removing 1. If the car radio unit has a security code, disable the code temporarily and enter it after connecting the battery; see manufacturer's instructions. 2. Disconnect the negative cable from the battery. 3....
Speakers — removal and installation Removing 1. Remove trim panel in footwell ( Section 11 ). 2. Remove the two screws securing the speaker to the footwell trim panel and remove the speaker, then disconnect its wiring (photo). Installation 3. Install in...
Radio antenna — general description 1. Models with a sunroof fitted as standard use a mesh radio antenna attached to the inside of the sunroof glass (photo). 2. The antenna is non-replaceable, please contact your Skoda dealer if a problem occurs. 3....