Electrical equipment of the car engine Skoda Felicia

Engine Electrical Specifications
Starting and charging systems General parameters System type 12 volt, negative grounded Starter Type Magneton Developed power, kW (at 12V voltage) Petrol engines 1.3 l produced before June 1995. 0.8 1.3L petrol engines...

Charging and Starting Systems — Information and Precautions
General information The starting and charging systems are the main components of the engine electrical equipment. Since the operation of these systems is related to the functioning of the engine, they are considered...

Checking the condition and charging the battery
Checking the condition of traditional and low maintenance batteries 1. If the average annual mileage of the vehicle is low, it is sufficient to check the specific gravity of the battery electrolyte to determine its...

Removal and installation the battery
Removal Caution! The negative cable should always be disconnected from the battery first and connected last! If the car is equipped with a Skoda branded audio system, make sure you have the code required to disable the...

Checking the proper functioning of the charging system
Note: See the warnings provided in Section General information and precautions . 1. If the charge indicator lamp on the dashboard of the car does not light when the ignition is turned on, first of all, you should check...

Removal and installation the generator
Longitudinal section of the generator 1 - Front cover; 2 - Back cover; 3 - Board with diodes; 4 - Slip rings; 5 - Rear bearing; 6 - Brush holder; 7 - Voltage regulator; 8 - Brushes; 9 - Stator with windings; 10 - Rotor;...

Replacing the brush holder/voltage regulator module
1. Remove the generator (see section Removal and installation the generator ). 2. Place the removed generator on a clean work surface with the pulley facing down. 3. On diesel and 1.6L models, loosen the mounting...

Checking the proper functioning of the starting system
1. The starter failure when the ignition key is turned to the appropriate position may occur for any of the following reasons: a) Battery is faulty; b) The quality of the electrical connection between the ignition...

Removal and installation the starter
Magneton 1.0 Starter Elements 1 - Front cover; 2 - Mounting screw M6x16; 3 - Washer; 4 - Drive lever; 5 - Overlay; 6 - Pin; 7 - Relay anchor; 8 - Spring; 9 - Traction relay; 10 - Washer; 11 - Spring ring; 12 - Nut M10;...

Starter overhaul
If you suspect that the starter is not functioning properly, it should be removed from the car and taken to a specialized auto repair shop for a thorough inspection and repair. In the vast majority of cases, the cause...

Ignition system of gasoline engines — general information
Ignition system diagram with contactless sensor-distributor 1 - Spark plugs; 2 - Ignition distributor; 3 - Switch; 4 - Ignition coil; 5 - Ignition switch; 6 - Battery Note: The Bosch Mono-Motronic, Simos 2P and...

Diagnosis of ignition system faults and testing of its components
Warning! When performing any maintenance work on system components with the ignition on, special precautions must be taken. Receiving an electric shock can lead to the most serious consequences. Persons with an...

Removal and installation the ignition coil
Removal Make sure the ignition is off, then disconnect the negative battery cable. Bosch Mono-Motronic System 1. The ignition coil is installed in the front part of the right wheel arch mudguard, next to the...

Removal and installation the ignition distributor
Distributor Ignition Components 1 - Rotor hub; 2 - Spring; 3 - Centrifugal governor counterweight; 4 - Body; 5 - Vacuum corrector membrane mechanism; 6 - Bearing; 7 - Screw M6x8; 8 - Retaining ring; 9 - Support plate;...

Checking and adjusting the ignition timing angle
Carburetor models 1. One of the distinctive features of contactless ignition systems is the high stability of the once set basic ignition advance. During the operation of the car, the initial angle practically does not...

Removal and installation of ignition system information sensors
Many of the sensors in the engine management system provide information that is used by both the fuel system and the ignition system. This Section discusses only those sensors that detect the operation of the ignition...

Diesel Engine Pre-Glow System — General Information
To facilitate cold starting, diesel engines are equipped with a pre-glow system, the components of which are four glow plugs, a control unit, a control lamp built into the instrument panel and a set of connecting...

Removal and installation pre-glow control system components
Removal Control unit 1. The control unit is located on the bracket at the rear of the left wheel arch mudguard, next to the pre-heating system relay. 2. Disconnect the negative cable from the battery. 3. If equipped,...

Checking the condition, removing and installing glow plugs
Examination 1. In case of malfunction of the system, the search for the cause of the failure is carried out by substituting known good components for the ones being checked, or using special diagnostic equipment in the...

This section is available on russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

Link to this section in various formats

TEXTHTMLBB Code

Felicia (1994-2001)