Upholstery and panels (Skoda Fabia 5J)

Removal and installation the upper panel (upholstery) of the A-pillar (vehicles without an inflatable airbag for head protection)

Using a lever action, release the top panel (upholstery) of the A-pillar "2" from the pillar, first at the top and then continue downwards. Disconnect the speaker plug connector (if it is part of the equipment). Remove the upper panel (upholstery) of the A-pillar.

Installation

Installation should be carried out in the reverse order of actions, and the following must be observed: Restore the position of the clamping clips "1" in the upper panel of the A-pillar "2" and, if damaged, replace them with new ones.

Removal and installation the upper panel (upholstery) of the A-pillar (vehicles with an inflatable airbag for head protection)

Important: If the upper trim panel of the A-pillar is forcibly removed, there is a risk of the head protection "Airbag" module deploying.

The extraction procedure is the same as for vehicles without an Airbag to protect the head.

Installation

Installation should be carried out in the reverse order of actions, and the following must be observed: Before connecting the battery, turn on the ignition.

Removal and installation the lower panel (upholstery) of the A-pillar

Remove the lower panel (upholstery) of the B-pillar. Remove the engine hood opening control lever (only on the driver's side). Remove screw "2" (only on the driver's side), 2 Nm. Remove the lower panel (upholstery) "1" by pulling.

Installation

Installation should be carried out in the reverse order of actions, and the following must be observed: Restore the position of the clamping clips "3" in the lower panel of the A-pillar "1", if damaged, replace with new ones.

Original text is located on (www.SKODABOOK.ru)

Removal and installation the upper panel (upholstery) of the B-pillar (vehicles without an inflatable airbag for head protection)

Remove cover "3". Remove screw -2 (2.5 Nm). Remove the seat belt mounting loop cover. Remove the seat belt screw. The upper panel of the B-pillar "1" should first be released from the door seal on the sides, and only then should it be gradually removed from the spring clips "4". The upper part is located under the shaped roof trim and fits into cutouts in the body.

Installation

Installation should be carried out in the reverse order of actions, and the following must be observed: Restore the position of the clamping clips in the upper panel of the B-pillar; if damaged, replace them with new ones.

Removal and installation the upper panel (upholstery) of the B-pillar (vehicles with an inflatable airbag for head protection)

Remove the casing with the inscription "Airbag" "3". The further extraction process is similar to that of vehicles without an Airbag to protect the head.

Installation

Installation should be carried out in the reverse order of actions, and the following must be observed: Restore the position of the clamping clips in the upper panel of the B-pillar; if necessary, replace them with new ones. Before connecting the battery, turn on the ignition.

Removal and installation the lower panel (upholstery) of the B-pillar

Partially remove the top panel of the B-pillar, especially its lower part that overlaps the bottom panel. Gradually release the clamping clips "1" of the B-pillar panel "2" from above. Pull out the lower panel (upholstery) of the B-pillar "2" in the upward direction "arrow". Disconnect the plug connector of the vehicle interior monitoring switch (only on the driver's side).

Installation

Installation should be carried out in the reverse order of actions, and the following must be observed: Restore the position of the clamping clips "1" in the lower panel of the B pillar "2", if damaged, replace them with new ones.

Removal and installation the upper panel (upholstery) of the C-pillar (vehicles without an inflatable airbag for head protection)

Remove cover "2". Remove screw -2 (2.5 Nm). Using eg. tool d.'; to remove the internal panels of the "MP8-602/1", gradually remove the panel - 4- from the clamping clamps "1". The panel should be removed.

Installation

Installation should be carried out in the reverse order of actions, and the following must be observed: Restore the position of the clamping clips "1" in the upper panel of the C-pillar "4", if damaged, replace with new ones.

Removal and installation the upper panel (upholstery) of the C-pillar (vehicles with an inflatable airbag for head protection)

Remove the screw cap labeled "Airbag." The removal procedure is the same for vehicles without an airbag.

Installation

Installation should be carried out in the reverse order of actions, and the following must be observed: Before connecting the battery, turn on the ignition.

Removal and installation the lower panel (upholstery) of the C-pillar

Remove the lower panel (trim) of the B-pillar. Remove the upper panel (trim) of the C-pillar. Remove the side trim (panel) of the trunk lid. Remove the rear seat. Remove screw "4" (1 Nm). Remove the clamp. Remove the lower panel of the C-pillar "2" from the clamp "3" in an upward direction. Installation should be carried out in the reverse order of actions.