1.9-liter diesel engines for the car Skoda Fabia 2

Engine number and parameters
Engine number The engine number ("engine letter code" and "factory serial number") is located at the front on the connecting flange of the engine and gearbox. Additionally, a sticker with the "engine letter code" and...

Removal the engine
Important: The engine is removed together with the gearbox in a downward direction. All cable clamps (bandages) that were loosened or cut during engine removal must be re-fastened in the same place when the engine is...

Engine installation
Progress of work Install the engine on the T10012 engine mount bracket. Installation is performed in reverse order, observing the following instructions. Important: When installing, replace the self-locking nuts and...

Unit support
Tightening torques Engine mount bracket 1 - 20 Nm + 90° (1/4 turn) - replace 2 - 30 Nm + 90° (1/4 turn) - replace Gearbox support 1 - 50 Nm + 90° (1/4 turn) - replace 2 - 40 Nm + 90° (1/4 turn) - replace Swinging...

Removal and installation a poly V-belt
Important: Before you begin removing the poly V-belt, you need to mark the direction of its movement. Reversing the direction of movement of a used belt can cause it to become unusable. When installing a poly V-belt,...

Removal the poly V-belt
Removal - cars without air conditioning Lift the engine cover at the sides "arrow A" and remove it forward "arrow B". Remove the upper boost air pipe "1" with connecting hose "2" "arrows". Mark the direction of rotation...

Removal the toothed drive belt
Important: Before you begin removing the timing belt, you must mark its direction of movement. Reversing the direction of movement of a used belt may cause it to become unusable. 1 - Upper part of the toothed drive belt...

Installing a toothed drive belt
Important: Adjustment work on the toothed drive belt may only be carried out when the engine is cold. When turning the camshaft, the crankshaft must not be at TDC with any piston. This could cause damage to the valves...

Removal and installation flange and flywheel seals
Important: To carry out assembly work, it is necessary to secure the engine with the engine support bracket "MP1-202" and spacer bushings "T30010" on the assembly stand. Flange and flywheel sealing gaskets 1 - PTFE...

Removal and installation the crankshaft
Removal and installation the crankshaft 1 - Bearing inserts 1,2,4 and 5-, for bearing caps without lubrication grooves, for cylinder blocks with lubrication grooves, do not mix up already used bearing inserts (mark); 2...

Cylinder head — removal and installation
Assembly diagram Important: Cylinder heads with cracks between the valve seats can be used without reducing their service life, if the cracks are small, maximum 0.5 mm wide. Additional machining of the cylinder head of...

Removal and installation the cylinder head cover
Lift the engine cover at the sides "arrow A" and remove it forward "arrow B". Remove the charge air pipe by slightly pulling out the retaining clips. For engines with the letter designation BSW Important: Coolant hoses...

Installing the cylinder head cover
Lift the engine cover at the sides "arrow A" and remove it forward "arrow B". Remove the charge air pipe by slightly pulling out the retaining clips. For engines with the letter designation BSW Important: Coolant hoses...

Removal the cylinder head cover
Remove the upper engine cover. Remove the air filter with the air intake sleeve. Remove the battery and battery holder. Remove the rear and lower boost air pipes. Disconnect the glow plug connector. For engines with the...

Repair of the valve timing mechanism
Important: After installing the camshaft, do not start the engine for approx. 30 minutes. The hydraulic tappets should settle. After completing work on the valve timing mechanism, carefully crank the engine at least 2...

This section is available on russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

Read similar sections on other Skoda models

➧ Diesel engines 1.6/2.0 l: Engine repair Skoda Octavia 3 (2013-2019)
➧ Power unit: Engine in car Skoda Favorit (1987-1994)

Link to this section in various formats

TEXTHTMLBB Code

Fabia 2 (2007-2014)