The braking system of car Skoda Fabia 2

Anti-lock braking system (ABS)
ABS and ESP devices are related to vehicle safety systems;working on them requires professional knowledge of the system. Checking, replacing or repairing ABS may only be carried out by specially trained mechanics....

Instructions for repair work on the anti-lock braking system ABS «BOSCH 8.0»
The hydraulic control unit for ABS, ABS/EDS/ASR and ABS/ASR/ESP "BOSCH 8.0" cannot be disassembled or repaired. If there are any faults or malfunctions, it is necessary to replace the hydraulic control device as a...

Basics of ABS Troubleshooting and Repair «BOSCH 8.0»
All control units are interconnected by two CAN-BUS data transmission wires. Therefore, before beginning troubleshooting, it is necessary to first scan the fault memory of all control units installed in the vehicle....

Distinctive marks of the ABS and ESP control units «BOSCH 8.0»
Assembly position for the "BOSCH 8.0" device Location of "ABS" for left-hand drive vehicles. 1 - Hydraulic control device 2 - Brake booster ABS, ABS/ASR "BOSCH 8.0", acc. The hydraulic control unit ABS/ASR/ESP "BOSCH...

Electrical/electronic parts and assembly points of ABS/ESP BOSCH 8.0
Assembly diagram - electrical/electronic components and assembly points of ABS/ESP BOSCH 8.0 1 - The hydraulic control unit ESP BOSCH 8.01, ABS/ASR/ESP, ABS/ASR/ESP BOSCH 8.0 must not be disassembled or repaired; 2 -...

Indication of faults by alarms
Important: When using a diagnostic tool, the electrical test is part of the "Guided Fault Finding" function. Dashboard Various instrument panel designs depending on the vehicle's equipment. Alarms Pos. Designation 1...

Hydraulic control unit (ABS BOSCH 8.0), brake booster and brake master cylinder
Assembly diagram of the hydraulic control unit, brake booster and brake master cylinder Important: Before you begin installing the brake line, you must install the bracket. During installation or connection, the brake...

Removal and installation of the hydraulic control device
Caution: Make sure that no brake fluid enters the plug connector of the hydraulic control unit. The fact is that otherwise the contacts corrode, resulting in device failure. If the plug connector is dirty, it must be...

Removal and installation the hydraulic control device holder
Removal and installation the ABS holder or ABS/ASR BOSCH 8.0, respectively. Remove the hydraulic control unit for ABS and ABS/ASR BOSCH 8.0, respectively. Remove the holder "4" from the centering pins of the holder "2"....

Removal and installation the ABS/ASR/ESP bracket BOSCH 8.0
Remove the BOSCH 8.0 ABS/ASR/ESP hydraulic control unit. Remove bracket 4 from the centering pins of bracket 2. Unscrew screws 3 (three pcs.). Remove bracket 2 from hydraulic control unit 1. Installation is performed in...

Connecting the brake lines
Important: Before you begin installing the brake line, you must install the bracket. During installation or connection, the brake line must not be bent. The brake hoses must be installed in such a way that they do not...

Removal and installation ABS components on the front and rear suspensions
Removal and installation the speed sensor on the front suspension - vehicles with BOSCH 8.0 ABS Raise the car. Disconnect the plug connector "1" of the speed sensor wire from the speed sensor. Remove the Allen screw...

Removal and installation the front speed sensor wire — vehicles with BOSCH 8.0 ABS
Important: Repair of shielded ABS device wires is prohibited. Disconnect the battery. Remove the engine cover. Vehicles with turbocharged diesel engines TDIPD Remove the upper charge air pipe "1" with the connecting...

Removal and installation the speed sensor on the rear suspension
Important: Removal and installation of the speed sensor is carried out in the same way on vehicles with drum brakes as with disc brakes. An image of a speed sensor on a vehicle with disc brakes is used. Raise the car....

Rear Speed Sensor Wire Repair — Vehicles with BOSCH 8.0 ABS
Important: Repair of the speed sensor wire is carried out in the same way on vehicles with drum brakes as on vehicles with disc brakes. Disconnect the battery. After unlocking the plug connector, disconnect it from the...

Removal and installation ESP components
Removal and installation the ESP sensor unit "G419" Important: The ESP sensor unit "G419" houses the lateral acceleration sensor "G200" and the instantaneous yaw rate sensor "G202" in a common housing. The ESP sensor...

Repair of the front wheel brake mechanism
Repair of the front wheel brake mechanism, FS-II disc wheel brake caliper Important: After replacing the brake pad friction linings, you should press the brake pedal firmly several times with the vehicle stationary to...

Removal and installation friction linings (segments) — FS-II disc wheel brake caliper
Remove the wheel. Important: When removing, mark the friction linings that you will be using again. They must be reinstalled in the same location, otherwise braking action will be uneven! When replacing the friction...

Front brake repair — disc brake caliper FS-III
Important: After replacing the brake pad friction linings, you should press the brake pedal firmly several times with the vehicle stationary to ensure that the friction linings are in their working position. Before you...

Removal and installation friction linings (segments) and calipers of the FS-III disc wheel brake mechanism
Remove the wheel. Important: Mark the friction linings when removing them (internal, external), which will be used again. They must be reinstalled in the same location, otherwise braking action will be uneven! When...

Front brake repair — disc brake caliper C54-II
Important: After replacing the brake pad friction linings, you should press the brake pedal firmly several times with the vehicle stationary to ensure that the friction linings are in their working position. Before you...

Removal and installation friction linings (segments) and caliper of the C54-II disc wheel brake mechanism
Remove the wheel. Important: When removing, mark the friction linings that you will be using again. They must be reinstalled in the same location, otherwise braking action will be uneven! When replacing the friction...

Repair of the rear wheel brake mechanism
Removal and installation the rear wheel brake mechanism - drum brake mechanism Important: After replacing the wheel brake cylinder and the rear axle brake mechanism, you must press the brake pedal firmly several times...

Repair of the rear wheel brake mechanism — drum brake mechanism
Important: Before removing the wheel brake cylinder, rear axle brake mechanism, or disconnecting the brake line from the wheel brake cylinder, it is necessary to secure the brake pedal with a spacer bar to hold the...

Removal and installation brake shoes — drum brakes
Remove the wheel. Remove the brake drum retaining screw. Release the brake by sliding the wedge through the hole for the brake drum fixing screw with a screwdriver in an upward direction. Remove the brake drum. Remove...

Removal and installation the rear wheel brake mechanism — disc brake mechanism
Important: After replacing the brake pad friction linings, you should press the brake pedal firmly several times with the vehicle stationary to ensure that the friction linings are in their working position. Brake line...

Removal and installation friction linings (segments) — disc brake mechanism
Important: When removing, mark the friction linings that you will be using again. They must be reinstalled in the same location, otherwise braking action will be uneven! When replacing the friction linings, do not...

Parking brake system (handbrake)
Assembly diagram of the parking brake system engagement lever 1 - Parking brake system engagement lever 2 - Handle of the parking brake system engagement lever Removal Use a screwdriver to release the pawl on the...

Removal and installation the parking brake cable
Release the parking brake lever. Remove the storage shelf and armrest. After loosening the adjusting nut "3", unhook the parking brake drive cable "1" from the alignment clamp "2". Remove the wheel. Raise the car....

Adjusting the parking brake lever
Adjusting the parking brake lever - drum brake mechanism Important: Thanks to the automatic adjustment of the clearance in the rear wheel brake mechanism, there is no need to adjust the hand lever for engaging the...

Adjusting the parking brake lever — disc brakes
Important: Thanks to the automatic adjustment of the rear wheel clearance, there is no need to adjust the hand lever of the parking brake system during operation. A new adjustment must be made if the parking brake...

Pedal mechanism, brake system control pedal
Assembly diagram of the pedal mechanism, brake system control pedal Caution: The brake pedal travel length must not be shortened by adding additional floor coverings to the vehicle. Self-locking nuts should be replaced...

Disconnecting the brake control pedal from the brake booster and connecting it
Disconnecting the brake control pedal from the brake booster Remove the lower cover on the driver's side. Remove the brake light switch. Important: For clarity, the illustration shows the brake control pedal being...

Removal and installation the pedal mechanism
Disconnect the battery. Remove the lower cover on the driver's side. Cars without air conditioning Remove the left footwell air duct nozzle. Cars with air conditioning Remove the left footwell air duct nozzle. Vehicles...

Removal and installation the brake control pedal
Remove the lower cover on the driver's side. Cars without air conditioning Remove the left footwell air duct nozzle. Cars with air conditioning Remove the left footwell air duct nozzle. Vehicles with the "Comfort"...

Repair of the disc brake caliper
Assembly diagram of the front wheel disc brake caliper FS-II Important: When repairing, install the complete set. New disc brake calipers are filled with brake fluid and have been de-aerated. Lightly lubricate the wheel...

Removal and installation the front wheel disc brake caliper piston FS-III
Removing and installing the piston is done in the same way as for the FS-III, FS-II, or C54-II disc brake caliper. Insert a wooden block to prevent damage to the piston when pushing it out. Press the piston out of the...

Removal and installation the rear wheel disc brake caliper piston
The reverse adjustment tool "T10165" should be installed so that the flange of the tool is adjacent to the piston. By turning the knurled flywheel of the reverse adjustment device to the left, the piston should be...

Brake booster, brake master cylinder
Assembly diagram of the brake booster, brake master cylinder Important: The complete brake master cylinder and brake booster can be replaced independently of each other. 1 - Brake booster, in gasoline engines the...

Removal and installation the brake master cylinder
Important: The brake master cylinder cannot be repaired. Remove the engine cover. Remove the air filter. Remove the battery and battery holder. Cover the area around the engine and gearbox with a sufficient number of...

Removal and installation the brake booster
Remove the engine cover. Remove the air filter. Remove the battery and battery holder. Cover the area around the engine and gearbox with a sufficient number of non-shedding rags. Disconnect the connector "1" from the...

Removal and installation a dual pump (tandem type) for fuel and vacuum supply
For vehicles with turbocharged diesel engines TDI PD In vehicles with turbocharged diesel engines, vacuum is supplied to the brake booster by a tandem pump (diesel engines).

Bleeding the hydraulic brake system
Removal air from the hydraulic brake system without using a device for filling the hydraulic brake drive and for removing air from it Important: Bleeding the hydraulic brake system on vehicles equipped with ABS is...

Load-dependent brake force regulator (brake drive mode valve), distribution valve
Assembly diagram of a load-sensing brake force regulator (brake drive mode valve) Important: After removing the brake lines, the connection holes on the brake force regulator must be sealed with plugs. The plugs should...

Removal and installation the load-dependent brake force regulator (brake drive mode valve)
After pressing the brake pedal, secure it with a brake pedal holding device. Place a catch pan under the brake force regulator to catch any leaking brake fluid. Mark the brake lines. Unscrew the brake lines "1", "2",...

This section is available on russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

Read similar sections on other Skoda models

➧ Chassis (running gear): Brake system Skoda Rapid 1 (2012-2022)
➧ Chassis (running gear): Brake system Skoda Octavia 1 (1996-2004)
➧ Chassis (running gear): Brake system Skoda Superb 2 (2008-2015)
➧ Chassis (running gear): Brake system Skoda Kodiaq 1 (2016-2024)
➧ Chassis (running gear): Brake system Skoda Yeti (2009-2017)
➧ Chassis (running gear): Brake system Skoda Felicia (1994-2001)

Link to this section in various formats

TEXTHTMLBB Code

Fabia 2 (2007-2014)