Electrical equipment and devices Skoda Fabia 2

Instrument cluster — general description
The instrument panel is available in three versions Basic execution The instrument panel is equipped with only two analog gauges (speedometer and tachometer). Between them there is a central display, which shows the...

Removal and installation the instrument panel
Caution: Before starting work on electrical equipment, with the ignition off, it is necessary to disconnect the wire connecting the battery terminal to the ground (body) of the vehicle. After pulling out the steering...

Loading the contact terminals of the plug connector on the instrument panel
Plug connector, 32-pin, green 1 - receiving and transmitting coil of immobilizer 1; 2 - high beam headlights; 3 - low beam headlights; 4 - oil level/temperature/oil sensor (cars with "WIV"); 5 - speedometer...

Replacing the instrument panel viewing glass
Important: Replacement of the sight glass must be carried out in a dust-free environment and with maximum cleanliness. Remove the instrument panel. The glass should be carefully released from the "arrow" clamps. The new...

Instrument cluster warning light symbols
Important: All alarms are made of light-emitting diodes. If the alarm fails, the instrument panel must be replaced. 1 - front fog lights; 2 - low beam headlights; 3 - high beam headlights; 4 - rear fog light; 5 - left...

Service interval indicator
Mode of action The electronic service interval indicator system includes, among other things, a time counter and two daily trip meters. The electronic system evaluates the contents of the instruments in such a way that...

Car Radio — General Instructions
Caution: Before starting work on electrical equipment, it is necessary, with the ignition off, to disconnect the cable that connects the battery terminal to the ground (body) of the vehicle. Car radios are protected...

Removal and installation a car radio
Radio receiver "Best" Insert the extraction tool into the holes (see picture) so that it enters into a fixed position. Pull the radio out of the instrument panel by pulling on the hinges of the device. Important: When...

Plug connectors on a car radio
Multi-pin plug connector "A", sixteen-pin, two-piece 1 - loudspeaker + back to right; 2 - loudspeaker + front right; 3 - loudspeaker + front left; 4 - loudspeaker + rear left; 5 - loudspeaker - back to the right; 6 -...

Removal and installation speakers
Removal and installation front and rear low frequency speakers Remove the door moldings. Disconnect the plug connector on the speaker. After drilling out the four arrow rivets with a suitable drill, remove the faulty...

Loading the contact pins of the plug connector on the CD changer
Multi-pin plug connector, twelve-pin 1 - "data CD out" (into a car radio); 2 - "CD-CLOCK out" (into a car radio); 3 - CD "mass"; 4 - "data CD in" (from a car radio); 5 - not busy; 6 - 12V voltage supply (from a car...

Removal and installation the roof antenna and replacing the antenna wires
For vehicles with a glass roof, the antenna is mounted at the rear and is tilted at 60 degrees from the roof plane. On vehicles with a solid roof, the antenna is located at the front and angled at 30 degrees from the...

Navigation system
General description The navigation system unit combines the functions of a car radio with a CD changer and a navigation system. The double DIN housing contains: a car radio "RDS"; TMS box for receiving messages about...

Plug connectors on the navigation system unit
Multi-pin plug connector "A", sixteen-pin, two-piece 1 - loudspeaker + back to right 2 - loudspeaker + front right 3 - loudspeaker + front left 4 - loudspeaker + rear left 5 - loudspeaker - back to the right 6 -...

Removal and installation the navigation system device
Carefully release the frame around the navigation system unit using a disassembly wedge. Remove the four screws "2" (1.5 Nm). Remove the navigation system unit from the instrument panel. Disconnect the antenna wire and...

Removal and installation the GPS navigation antenna
The antenna is located under the instrument panel on the driver's side above the "Convenience" system electrical equipment control unit "J393". After removing the Comfort system electrical equipment control unit "J393"...

Telephone installation
Preparing for the phone The telephone installation is available in two different designs. Either as a basic phone preparation or as a universal phone preparation. Phone Preparation 1 (Basic) 1 - antenna for car radio...

Removal and installation the control unit for servicing the J412 telephone (interface box)
The control unit is located under the passenger seat next to the driver under the carpet. Remove the seat next to the driver. Remove the lower trim (panel) of the A and B pillars. Lift the carpet. Disconnect plug...

Removal and installation the microphone for the R38 phone
The microphone is located in the interior lighting of the body. Remove the interior body lighting. After disconnecting the plug connector "1", release the microphone "2" from the clamping clips of the interior body...

Multifunctional module «J527» — removal and installation
The multifunctional module is located on the left side in front of the switch on the steering column, and it is supplied in two versions: audio control, audio + telephone control. Important: The multifunctional module...

Windscreen washers — removal and installation
Removal and installation the windshield washer reservoir Remove the left wheel arch (fender) liner and the front bumper. Disconnect the plug connector from the windshield washer pumps "3", headlight washers "7" and from...

Removal and installation windshield wiper spray nozzles
Important: The jets are installed either with or without heating depending on the equipment and cannot be adjusted. Remove the windshield wiper arms with blades "1". Remove the waterproof housing cover "2". If...

Removal and installation windshield wipers
Removal and installation levers with brushes and adjusting their end position Using a screwdriver, remove both nut caps on the windshield wiper arms. After loosening the arrow nuts, fold back the windshield wiper arms...

Removal and installation the rear window wiper
Removal and installation the windshield wiper arm and adjusting its end position Flip back the cap. Loosen the "arrow" nut. Lift the wiper arm and release it from the cone using a rocking motion. After unscrewing the...

Replacing and adjusting the spray nozzle
Fold back the rear window wiper cap. Carefully pull out the windshield washer nozzle using suitable pliers in the direction of the arrow. Installation Adjust the windshield wiper to the end position. Insert the...

Headlight washers — removal and installation
Removal and installation the spray nozzle holder If only the spray nozzle holder is removed, there is no need to remove the bumper. Spray nozzles with cap 1 - should be pulled out a little from the bumper by grasping...

Removal and installation the headlight washer cylinder
The spray nozzles with cap "1" should be pulled out a little from the bumper by grasping the cap evenly on both sides in your hand, then grabbing the washers and pulling them out as far as they will go. Cap "1" should...

Removal and installation the switch on the steering column
Remove the steering wheel. Important: The steering wheel must be in the center position before removing from the steering column (the wheels are set to move straight). There is no locking pin on the return ring to lock...

Removal and installation the return ring with the guide coil spring from the switch on the steering column
Important: Vehicles with ESP and/or fog lights with the function "Cornerlicht" for turning, they are also equipped with an additional steering wheel angle sensor "G85", built into the same housing together with the...

Adjusting the center position of the return ring with a guide coil spring
It is carried out only if there are doubts about the correct adjustment of the middle position of the return ring rotor. Methodology The front wheels should be adjusted to move straight ahead. The rotor of ring "1"...

Ignition switch
Removal and installation the lock cylinder Remove the steering wheel. Remove the upper and lower steering column covers. Carefully disconnect the "arrow" plug connector of the immobilizer reading coil on the lock...

Removal and installation the ignition switch
Remove the upper and lower steering column covers. Disconnect the plug connector from the ignition switch and instruments. Remove the retaining varnish from both support screws "A." Loosen the support screws "A" and...

Parking assistance equipment — Parktronic
Assembly diagram 1 - Device for sound signaling equipment, to facilitate parking "N15" under the lower panel of the left B-pillar 2 - Parking aid control unit "J446", under the left side panel of the trunk 3 - Equipment...

Removal and installation the J446 parking aid control unit
Remove the left side panel of the trunk. After unscrewing the nuts (1.5 Nm), remove the equipment control unit to facilitate parking. After unlocking the plug connectors, remove them. Installation Installation is...

Removal and installation of the sound signaling device for the parking assistance equipment «N15»
Remove the lower panel of the B-pillar. Remove the plastic expansion rivets "arrows". Disconnect the plug connector. Installation is carried out in the reverse order of actions.

Removal and installation parking aid equipment sensors
Important: If you replace the bumper, you must glue new sensor holders into the new bumper, the visible part of which is painted with varnish in the color of the bumper. The internal and external sensor holders are not...

Removal and installation the light switch (light switch)
Turn light switch to position "0". Press the light switch firmly "arrow 1", rotate slightly to the right "arrow 2". Holding it in this position, pull it forward "arrow 3". Disconnect the connector on the switch....

Removal and installation the potentiometer for the headlight leveling system
After removing fuse box "2", lower it down so that it hangs down. To free up the wiring, remove light switch "1" and install the plug connector behind the instrument panel. At the bottom of the "arrow" you should insert...

Removal and installation switches in the center instrument panel
Lightly press the switch housing "arrow A". Carefully release the switch housing from the clamp "arrow B" using a disassembly wedge. Using two screwdrivers, carefully pry the corresponding switch out of the middle...

Removal and installation the hazard warning light switch
Using two disassembly clips, carefully release the switch from the middle blower nozzle of the "arrow". Disconnect the plug connector on the switch. Installation is carried out in the reverse order of actions.

Removal and installation the switch for adjusting the position of the rear-view mirrors
Remove the driver's door molding. Disconnect the plug connector and release the switch from the "arrow" latches using a small screwdriver. Pull the switch toward you. Installation is carried out in the reverse order of...

Removal and installation power window switches
Removal the switches in the driver's door (electric windows in all doors) Remove door handle cover "1". Slide control element "2" slightly forward "arrow A". Tilt control element slightly upward "arrow B" and remove it...

Removal and installation the switch for controlling the central locking system from the inside
Remove the middle panel (panel of the protruding part of the floor between the front seats) between the driver and the front seat passenger. Using a small screwdriver, release the switch from the "arrow" latches and...

Removal and installation seat heating switches
Remove the middle panel (panel of the protruding part of the floor between the front seats) between the driver and the front seat passenger. Using two screwdrivers "1", release the seat heating switch "2" from the clips...

Removal and installation the switch to deactivate the vehicle's interior monitoring device
Remove driver's door molding "2". Disconnect the plug connector on the switch. Pressing the retaining tabs on the sides, remove switch "1" from the molding. Installation is carried out in the reverse order of actions.

Horn — removal and installation
Carefully squeeze the plastic cover out of the bumper clamps at the front left. Unscrew the support screw "1" (16 Nm). Disconnect plug-in connector "2". Pull out horn "3" forward. Installation is performed in the...

Anti-theft alarm device
General description The functions of the anti-theft alarm system are integrated into the "J393" comfort system electrical control unit. The anti-theft alarm system is equipped with an automatic control system...

Removal and installation the siren of the anti-theft alarm device
Important: The siren of the "N12" anti-theft alarm system has its own backup power source, which cannot be replaced independently. Remove the waterproof casing cover, protective grille and air inlet housing cover "1"....

Removal and installation the vehicle interior monitoring device sensor and vehicle tilt sensor
Remove the glasses storage box from the roof trim. Disconnect the plug connector. Release the sensor set from the arrow clips and remove.

Removal and installation the fuse box from the instrument panel
The fuse box is located under a plastic cover on the left side of the instrument panel below the steering wheel. There is a light switch next to the box (daylight) and a central plug for connecting the diagnostic stand...

Removal and installation the fuse box on the battery
The battery fuse box is located on the holder above the battery. The battery fuse box is removed along with the fuse holder. Separating the battery fuse box from the fuse holder and connecting them. Disconnect the wire...

Disconnecting the fuse box on the battery from the fuse holder
Loosen nuts "1" (6 Nm). Remove spring washers "2" and fuses "3". Remove the fuse holder "4" from the battery fuse box support plate "5". Compound The connection of the fuse box on the battery and the fuse holder is...

Removal the relay from the relay cabinet and installing it
Remove the shock absorber panel under the instrument panel on the driver's side. After removing fuse box "1" from the instrument panel, lower it down so that it hangs down. For better visibility of the location of...

Control units
Central control unit for electrical on-board network "J519" general description Important: The J533 data bus diagnostic interface (gateway) is integrated into the J519 central control unit for electrical onboard power...

Removal and installation the central control unit of the electrical on-board network
The control unit is located on the driver's side behind the instrument panel to the left. Turn off the ignition, all electrical consumers and remove the key from the ignition switch. Remove the shock absorber panel...

Comfort system electrical equipment control unit — general description
The "J393" comfort system electrical equipment control unit has the following functions in the vehicle: control of the central door locking system, control of the anti-theft alarm system, locking the trunk lid, comfort...

Removal and installation the Comfort system electrical equipment control unit
Turn off the ignition, all electrical consumers and remove the key from the ignition switch. Remove the shock absorber panel under the instrument panel on the driver's side. Remove the driver's side footwell air vent....

This section is available on russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

Read similar sections on other Skoda models

➧ Electrical equipment: Equipment and devices Skoda Rapid 1 (2012-2022)
➧ Electrical equipment: Equipment and devices Skoda Octavia 1 (1996-2004)
➧ Electrical equipment: Equipment and devices Skoda Superb 2 (2008-2015)
➧ Electrical equipment: Equipment and devices Skoda Kodiaq 1 (2016-2024)
➧ Electrical equipment: Equipment and devices Skoda Yeti (2009-2017)
➧ Electrical equipment: Equipment and devices Skoda Felicia (1994-2001)

Link to this section in various formats

TEXTHTMLBB Code

Fabia 2 (2007-2014)