Car steering system Skoda Fabia 2

Steering column
Important: The steering column must not be repaired. Self-locking screws and nuts must be replaced. Welding and straightening work is not permitted on steering components. The steering columns are supplied as a spare...

Steering column control
Optical control Check the steering column components for damage. If damage is obvious, the entire steering column must be replaced. Action check Prerequisite for the implementation of control The universal joint with...

Removal and installation the steering column
Important: New steering columns supplied as spare parts are equipped with a transport lock. After installation of the steering column, the transport safety device must be removed. The steering columns are supplied as a...

Removal and installation the steering wheel lock
Important: Follow the instructions for reconnecting the battery. Disconnect the battery. Remove the steering wheel airbag and steering wheel. Remove the instrument panel with the upper steering shaft trim. Remove the...

Power steering mechanism
Design and method of operation EPHS electrohydraulic power steering (Electrically Powered Hydraulic Steering) - is a power steering mechanism that uses its own electric motor to drive the pump. 1 - Power steering; 2 -...

Removal and installation the TRW power steering gear housing
Important: Apart from replacing the cuff, tie rod end and tie rod, no other repair work is permitted on the steering gear housing. When working on a power steering system, it is essential to maintain maximum...

Power steering sensor «G250» and hydraulic lines for power steering
Removal and installation the G250 power steering sensor and the TRW power steering sensor wire Disconnect the battery. Important: For better access to the wire holders, it is possible to remove the air filter. Raise the...

Removal and installation of TRW hydraulic system pipelines
Notes on working on hydraulic system pipelines Some of the working fluid for hydraulic systems remains after draining, both in the pump unit and in the return line and in the discharge hose. Drained hydraulic fluid...

Control and adjustment of the power steering gear housing
Control and adjustment are provided on the TRW power steering gear housing. The KOYO power steering gear housing is checked and adjusted in the same manner as the TRW power steering gear housing. Checking and, if...

Disassembling and assembling the power steering gear housing
Disassembling and assembling the TRW power steering gear housing Important: After a vehicle accident or if the front axle is damaged, the damaged parts must be replaced. Repair of the power steering gear housing is not...

Tie rod ends, tie rods for power steering system
Checking the seals, clearances and fastening of the tie rod ends Check the clearance with the vehicle raised (the wheels are not loaded), moving the steering linkage rods and wheels. Required clearance value: no...

Removal and installation the tie rod end
Tie rod ends can be replaced with the tie rods and power steering housing installed. Raise the car. Remove the front wheel. Nut "1" should be unscrewed to such an extent that the puller rests on the nut. Using a puller,...

Removal and installation steering linkage rods
Important: The tie rod can only be removed and installed on a removed power steering gear housing. Remove the power steering gear housing. Clean the outside of the power steering housing in the area around the cuff...

Power steering pump unit
Assembly diagram of the TRW pump unit The steering pump unit is a complete assembly consisting of the power steering pump "V119" (electric motor and gear pump), the J500 power steering control unit and hydraulic fluid...

Power steering pump unit control
TRW power steering pump units can also be tested in a different way than the methods described in this section; e.g. within the framework of automatic control (self-diagnosis).

Removal and installation the TRW power steering pump unit
Important: Drained hydraulic fluid cannot be reused. Some of the working fluid for hydraulic systems remains after draining in the pump unit and in the hydraulic system pipelines. Do not clamp hydraulic system lines...

Replacing the receiver of the power steering pump unit
Important: When replacing the receiver, it is necessary to strictly monitor cleanliness. Thoroughly clean the space between the return line connection on the receiver and the pressure line connection on the pump unit;...

Checking the tightness of the power steering system
Important: Due to the fact that different versions use batteries of different sizes, it may happen that the receiver cover with the level indicator is covered by the battery holder. In this case, it is necessary to...

Noises when operating the power steering mechanism
Noise Elimination Guidelines A closed hydraulic system is a source of operating noise. Noise from the power steering always occurs when the steering wheel is turned to the extreme position; the steering wheel can only...

This section is available on russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

Read similar sections on other Skoda models

➧ Chassis (running gear): Steering Skoda Rapid 1 (2012-2022)
➧ Chassis (running gear): Steering Skoda Octavia 3 (2013-2019)
➧ Chassis (running gear): Steering Skoda Superb 2 (2008-2015)
➧ Chassis (running gear): Steering system Skoda Kodiaq 1 (2016-2024)
➧ Chassis (running gear): Steering Skoda Yeti (2009-2017)
➧ Chassis (running gear): Steering Skoda Felicia (1994-2001)

Link to this section in various formats

TEXTHTMLBB Code

Fabia 2 (2007-2014)